AGMA-6033-B98-1998.pdf
《AGMA-6033-B98-1998.pdf》由会员分享,可在线阅读,更多相关《AGMA-6033-B98-1998.pdf(56页珍藏版)》请在三一文库上搜索。
1、ANSI/AGMA 6033B98 ANSI/AGMA 6033B98 (Revision of ANSI/AGMA 6033A88) AMERICAN NATIONAL STANDARD Materials for Marine Propulsion Gearing Copyright American Gear Manufacturers Association Provided by IHS under license with AGMA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/
2、2007 03:53:04 MDTNo reproduction or networking permitted without license from IHS -,-,- Return to Menu ii Materials for Marine Propulsion Gearing ANSI/AGMA 6033B98 Revision of ANSI/AGMA 6033A88 Approval of an American National Standard requires verification by ANSI that the require- ments for due pr
3、ocess, consensus, and other criteria for approval have been met by the standards developer. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Substantial agreement means much mor
4、e than a simple majority, but not necessarily una- nimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The use of American National Standards is completely voluntary; their existence does not in any respect preclude any
5、one, whether he has approved the standards or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any A
6、merican National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute. Requests for interpre- tation of this standard should be addressed to the American Gear Manufacturers
7、 Association. CAUTION NOTICE: AGMA technical publications are subject to constant improvement, revision, or withdrawal as dictated by experience. Any person who refers to any AGMA Technical Publication should be sure that the publication is the latest available from the Association on the subject ma
8、tter. Tables and other selfsupporting sections may be quoted or extracted in their entirety. Credit lines should read: Extracted from ANSI/AGMA 6033B98, Materials for Marine Propulsion Gearing, with permission of the publisher, American Gear Manufacturers Association, 1500 King Street, Suite 201, Al
9、exandria, Virginia 22314. Approved June 19, 1998 ABSTRACT This document identifies commonly used alloy steels, heat treatments and inspection requirements for through hardened, case hardened and surface hardened gearing for main propulsion marine service over 1500 hp. Forged and hot rolled alloy ste
10、el bar stock are specified to three metallurgical quality grades (I, II and III) accord- ing to cleanliness and test requirements. Cast steel gearing is specified to a single metallurgical quality level. Mechanical, metallurgical and nondestructive test requirements are provided for various heat tre
11、at processes and metallurgical quality grades of gearing. Published by American Gear Manufacturers Association 1500 King Street, Suite 201, Alexandria, Virginia 22314 Copyright 1998 by American Gear Manufacturers Association All rights reserved. No part of this publication may be reproduced in any f
12、orm, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United States of America ISBN: 1555897118 American National Standard Copyright American Gear Manufacturers Association Provided by IHS under license with AGMA Licensee=IHS Employees
13、/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 03:53:04 MDTNo reproduction or networking permitted without license from IHS -,-,- Return to Menu ANSI/AGMA 6033B98AMERICAN NATIONAL STANDARD iii Contents Page Forewordiv. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14、. . . . . . . . . . . . . . . . . . . . . . . . . . . 1Scope1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2References1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15、 . . . . . . 3Definitions3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Testing and certification8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Maximum controlling section size9. .
16、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Forged rings for through hardened gears10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Forgings and bar stock for through hardened pinions and gears12. . . . . . . . . . . 8Cast through hardened gears16. . .
17、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Carburized pinions and gears20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Nitrided pinions and gears25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18、 . . . . 11 Induction hardened pinions and gears29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Magnetic particle inspection of finished gearing from alloy steel forgings and bar stock34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19、 . . . . . . . . . . 13 Ultrasonic inspection of gearing blanks from alloy steel forgings and bar stock35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Ultrasonic inspection of cast gears36. . . . . . . . . . . . . . . . . . .
20、 . . . . . . . . . . . . . . . . . . 15 Metallographic examination37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tables 1Chemical requirements for through hardened alloy steel forged rings10. . . . . . . 2Approximate maximum controlling section sizes for thro
21、ugh hardened alloy steel forged rings10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Minimum tempering temperatures for through hardened alloy steel forged rings11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22、. . . . . . . . . . . . . . . . . . . . . . . 4Mechanical property requirements for through hardened alloy steel forged rings11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Chemical requirements for through hardened alloy
23、 steel forgings and bar stock for gearing13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Approximate maximum round controlling section sizes for through hardened alloy steel forgings and bar stock for gearing14. . . . . . . . . . . . . . . .
24、 . . . . . . . . . . . . 7Minimum tempering temperatures for through hardened alloy steel forgings and bar stock for gearing14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Mechanical property requirements for through hardened alloy steel forgings and bar
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AGMA 6033 B98 1998
链接地址:https://www.31doc.com/p-3728672.html