ABMA-STD-18.1-1982-R1999.pdf
《ABMA-STD-18.1-1982-R1999.pdf》由会员分享,可在线阅读,更多相关《ABMA-STD-18.1-1982-R1999.pdf(48页珍藏版)》请在三一文库上搜索。
1、. . 2595532 O079772 587 ANSVABMA 18.1 ADOPTION NOTICE ANSVABMA 18.1 , “Bearing Needle Roller and Needle Roller Bearings Metric Design”, w a s adopted on 15 August I995 for use by the Department of Defense O D ) . Proposed changes by DoD Activities must be submitted to the DoD Adopting Activity: Defe
2、nse Industrial Supply Center, A”: DISC-EC, 700 Robbin distribution is unlimited. Copyright American Bearing Manufacturers Association Provided by IHS under license with ABMA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/24/2007 09:38:49 MDTNo reproduction or networking perm
3、itted without license from IHS -,-,- b ABMA COPYRIGHT NOTICE Copyright* American Bearing Manufacturers Association, Inc., 1 982 These materials have been prepared by the American Bearing Manufacturers Association, Inc. However the information contained in these materials has not been independently v
4、erified by the American Bearing Manufacturers Association or Information Handling Services, Inc. Neither organization warrants or assumes any liability for the accuracy or completeness of these materials. Copyright American Bearing Manufacturers Association Provided by IHS under license with ABMA Li
5、censee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/24/2007 09:38:49 MDTNo reproduction or networking permitted without license from IHS -,-,- AFBMA 18.3 82 W 0873073 0000503 T22 D ! i 1 -. i AMERICAN NATIONAL STANDARD AFBMA STANDARD NEEDLE ROLLER BEARINGS RADIAL, METRIC DESIGN Spo
6、nsor The Anti-Friction Bearing Manufacturers Association, Inc. Approved December 2,1982 American National Standards Institute, Inc. REAPPROVE D, ANSI/ AFBMA (Revision of ANSIIAFBMA Std. 18.1-1982 1 8 . 1 - 1 9 7 6 ) Copyright American Bearing Manufacturers Association Provided by IHS under license w
7、ith ABMA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/24/2007 09:38:49 MDTNo reproduction or networking permitted without license from IHS -,-,- AFBMA 38.3 82 m 0873073 0000504 Yb9 . . . ., I . . - . . . ; , . . . . American National Standard An American National Standard
8、implies a consensus of those sub- stantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he
9、 has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. CAUTION NOTICE: This American Na
10、tional Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm. revise, or withdraw this standard no later than five years from the date of publication. Purchasers of American National Standards may receiv
11、e current information on all standards by calling or writing the American National Standards Institute. Published by The Anti-Friction Bearing Manufacturers Association, Inc. 1235 Jefferson Davis Highway, Suite 704 Arlington, Virginia 22202 Copyright 1983 by The Anti-Friction Bearing Manufacturers A
12、ssociation, Inc. Copyright American Bearing Manufacturers Association Provided by IHS under license with ABMA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/24/2007 09:38:49 MDTNo reproduction or networking permitted without license from IHS -,-,- AFBMA 38.3 82 0873073 00005
13、05 8T5 FOREWORD (This foreword is not a part of American National Standard 18.1-1976, Metric Design Radial Needle Roller Bearings.) This Standard comprises a revision of ANSIIAFBMA 18.1-1976, Metric Design Radial Needle Roller Bearings. All material which relates only to Inch Design Product will be
14、found in Standard 18.2. Most of the Table numbers have been changed. Using the numbering se- quence in this standard, major changes have been made to Tables 4.3, 5.7 and 5.8. Minor changes have been made to most of the other Tables. The material in this standard conforms, where possible, to recommen
15、dations of the International Standards Organization, Technical Committee 4, Rolling Contact Bearings, in whose work the U.S.A. has actively participated through delegates officially appointed by the American National Standards Institute. Copies of IS0 Recommendations concerning Rolling Contact Beari
16、ngs (Ball and Roller Bearings) are available from the American National Standards Insti- tute, Inc., 1430 Broadway, New York, N.Y. 10018. Suggestions for the improvement of this standard gained through experience with its use will be welcomed. These should be sent to the American National Standards
17、Institute, Inc., 1430 Broadway, New York, N.Y. 10018. The officers of Sectional Committee 83 of the American National Standards Institute and the organizations represented at the time this standard was sub- mitted are as follows: R. E. Murtera, Chairman J. J. Whitsett, Secretary American Gear Manufa
18、cturers Association American Society of Mechanical Engineers Anti-Friction Bearing Manufacturers Association Hydraulic Institute National Electrical Manufacturers Association National Machine Tool Builders Association Society of Automotive Engineers Society of Manufacturing Engineers U.S. Department
19、 of the Air Force U.S. Department of Defense, DISC U.S. Department of the Navy Copyright American Bearing Manufacturers Association Provided by IHS under license with ABMA Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/24/2007 09:38:49 MDTNo reproduction or networking permit
20、ted without license from IHS -,-,- Other related AFBMA Standards for Ball and Roller Bearings and Balls 1 -Terminology 4 -Tolerance Definitions and Gaging Practices 7 -Shaft and Housing Fits for Metric Radial Ball and Roller Bearings (Except Tapered Roller Bearings) Conforming to Basic Boundary Plan
21、s 8.2 - Ball and Roller Bearing Mounting Accessories, Inch Design 9 - Load Ratings and Fatigue Life for Ball Bearings 10 - Metal Balls 11 12 - Instrument Ball Bearings 13 - Roller Bearing Vibration and Noise 14 - Housing for Bearings With Spherical Outside Surfaces 15 - Ball Bearings With Spherical
22、Outside Surfaces and Extended - Load Ratings and Fatigue Life for Roller Bearings Inner Ring Width (Includes Eccentric Locking Collars) 16.2 -Airframe Ball, Roller and Needle Roller Bearing, Inch Design 17 18.1 - Needle Roller Bearings - Radial, Metric Design - Needle Rollers, Metric Design 18.2 - N
23、eedle Roller Bearings - Radial, Inch Design 19 - Tapered Roller Bearings, Radial, Inch Design 20 - Metric Ball and Roller Bearings (Except Tapered Roller-Bearings) Conforming to Basic Boundary Plans 21 - Metric Thrust Needle Roller and Cage Assemblies and Thrust Washers 21.2 - Thrust Bearings of Bal
24、l, Cylindrical Roller, Tapered Roller and Needle Roller Types, Inch Design 22 - Spherical Plain Bearings, Joint Type An AFBMA Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. ,The existence of an AFBMA Standard does not in any respect preclude anyone, wh
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ABMA STD 18.1 1982 R1999
链接地址:https://www.31doc.com/p-3729648.html