AS-3711.10-2000.pdf
《AS-3711.10-2000.pdf》由会员分享,可在线阅读,更多相关《AS-3711.10-2000.pdf(80页珍藏版)》请在三一文库上搜索。
1、AS 3711.102000 Australian Standard Freight containers Part 10: Handling and securing Modified and containing the full text of ISO 3874:1997, including ISO/DIS 3874:1998 AS 3711.10 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 This Australian Standard was prepared by Committee ME/68, Freig
2、ht Containers. It was approved on behalf of the Council of Standards Australia on 31 August 1999 and published on 24 January 2000. The following interests are represented on Committee ME/68: Australasian Railway Association Australian Chamber of Shipping Australian Maritime Safety Authority AUSTROAD
3、S Department of Defence (Australia) Germanischer Lloyd National Freight Forwarders Association National Road Transport Commission Keeping Standards up-to-date Standards are living documents which refl ect progress in science, technology and systems To maintain their currency, all Standards are perio
4、dically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was pu
5、rchased. Detailed information about Standards can be found by visiting the Standards Australia web site at .au and looking up the relevant Standard in the on-line catalogue. Alternatively, the printed Catalogue provides information current at 1 January each year, and the monthly magazine, The Austra
6、lian Standard, has a full listing of revisions and amendments published each month. We also welcome suggestions for the improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Contact us via email at mail .au, or write to t
7、he Chief Executive, Standards AustraliaInternational Ltd. POBox 1055, Strathfi eld., NSW 2135. This Standard was issued in draft form for comment as DR 98597. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 AS 3711.102000 Australian Standard Freight containers Part 10: Handling and securing
8、 Originated as AS/NZS 3711.10:1993. Revised and designated as AS 3711.102000. COPYRIGHT Standards Australia International All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permi
9、ssion of the publisher. Published by Standards Australia International Ltd PO Box 1055, Strathfield, NSW 2135, Australia ISBN 0 7337 2942 8 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 ii PREFACE This Standard was prepared by the Standards Australia Committee ME/68, Freight Containers to
10、 supersede AS/NZS 3711.10:1993. It modifi es and has been reproduced from ISO 3874:1997, Series 1 freight containersHandling and securing and its draft Amendment No. 1, ISO/DIS 3874:1998. This Standard is Part 10 of the AS or AS/NZS 3711, Freight containers series. The series comprises AS 3711.1Part
11、 1: Classifi cation, dimensions and ratings AS/NZS 3711.2Part 2:Terminology AS/NZS 3711.3Part 3: Corner fi ttings AS/NZS 3711.4Part 4:General purpose containers AS 3711.5Part 5:Thermal containers AS 3711.6Part 6:Tank containers AS/NZS 3711.7Part 7:Dry bulk containers AS 3711.8Part 8:Platform contain
12、ers AS 3711.9Part 9: Coding, identifi cation and marking AS 3711.10Part 10:Handling and securing Changes since the last edition include the following: (a)Changes introduced in ISO 3874:1997. (b)Changes (through Appendix ZZ) to include requirements for Series R containers. (c)Inclusion of grappler li
13、ft. (d)Inclusion of straddler lift. (e)Inclusion of draft Amendment 1 to ISO 3874:1997/DAMI. The number of this Standard is not reproduced on each page. Its identity is shown only on the cover and the title page. Statements expressed in mandatory terms in the following notes to the text are deemed t
14、o be requirements of this Joint Standard: Note 2 to Table 4 of Clause 6.3.3, the note to Figure 9 of Clause 6.6.1, and the Note to Figure 13 of Clause 6.9.1. For the purposes of this Standard, the text of ISO 3874:1997 should be modifi ed as follows: (i)Substitute Australian Standard for Internation
15、al Standard wherever it occurs. (ii)Substitute a full point (.) for a comma (,) as a decimal marker. (iii)Annexes B to E from draft Amendment 1 to ISO 3874 have been added to the ISO text. (iv)Variations between ISO 3874 and this Standard, for application in Australia, are set out in Appendix ZZ. Th
16、ese variations are indicated by a marginal bar against each clause, table, fi gure or part thereof affected. (v)Replace references to other publications by references to Australian or Australian/New Zealand Standards as follows: Reference to International StandardAustralian or Australian/New Zealand
17、 Standard ISOAS 668Series 1 freight containers Classifi cation, dimensions and ratings 3711Freight containers 3711.1 Part 1: Classifi cation, dimensions and ratings ISOAS/NZS 830Freight containersTerminology3711.2Part 2: Terminology 1161Series 1 freight containersCorner fi ttingsSpecifi cations 3711
18、.3 Part 3: Corner fi ttings Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 iii 1496Series 1 freight containers Specifi cation and testing 1496-1 Part 1: General cargo containers for general purposes 1496-2 Part 2: Thermal containers 1496-3 Part 3: Tank containers for liquids, gases and pre
19、ssurized dry bulk 1496-4 Part 4: Non-pressurized containers for dry bulk 1496-5 Part 5: Platform and platform-based containers 3711.4Part 4: General purpose containers AS 3711.5Part 5: Thermal containers 3711.6Part 6: Tank containers AS/NZS 3711.7Part 7: Dry bulk containers AS 3711.8Part 8: Platform
20、 containers 6346Freight containersCoding, identifi cation and marking 3711.9 Part 9: Coding, identifi cation and marking The terms normative and informative have been used in this Standard to defi ne the application of the appendix to which they apply. A normative appendix is an integral part of a S
21、tandard, whereas an informative appendix is only for information and guidance. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Fe
22、b 2009 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 27 Feb 2009 ISO ISO 3874:1997(E) 7 Table 3 Applicability of top lift spreader
23、s Key :AllowedNot allowed (or not applicable) Empty containerContainer type ISO 6346Loaded container AAA AAAAXBBB BB BBXCCCCXDDXAAA AAAAXBBB BBBBX CCCCXDDX General purposeGP,VH Open topUT Bulk: non-pressurized/boxBU ThermalRE,RT RS Tank for liquids and gasesTN,TD TG Bulk: non-pressurized/hopper pres
24、surizedBK PlatformPL1)1)1)1) complete and fixed endsPF fixed free standing postsPF complete and folding ends, erected condition PC folding free standing posts, erected condition PC complete and folding ends, folded condition PC folding free standing posts, folded condition PC Platform-based with com
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AS 3711.10 2000
链接地址:https://www.31doc.com/p-3730183.html