BHMA-A156.14-2007.pdf
《BHMA-A156.14-2007.pdf》由会员分享,可在线阅读,更多相关《BHMA-A156.14-2007.pdf(27页珍藏版)》请在三一文库上搜索。
1、 ANSI/BHMA A156.14 - 2007 Revision of ANSI/BHMA A156.14-2002 AMERICAN NATIONAL STANDARD FOR SLIDING AND FOLDING DOOR HARDWARE SPONSOR BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. AMERICAN NATIONAL STANDARDS INSTITUTE Approved September 12, 2007 Copyright Builders Hardware Manufacturers Associat
2、ion Inc. Provided by IHS under license with BHMA Licensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 01:31:06 MDTNo reproduction or networking permitted without license from IHS -,-,- 2 AMERICAN NATIONAL STANDARD An American National Standard implies a consensus of those su
3、bstantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he has approved the standard or not
4、, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. CAUTION NOTICE: This American National Standard may be revised or
5、 withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication. Purchasers of American National Standards may receive current information on all stan
6、dards by calling or writing the American National Standards Institute. Published by BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. 355 Lexington Avenue NEW YORK, NY 10017 Copyright 2007 by the Builders Hardware Manufacturers Association, Inc. Not to be reproduced without specific authorization f
7、rom BHMA Printed in the USA This Standard was first published in July 1980 by the Builders Hardware Manufacturers Association, Inc. It was entitled, “Standard 301 BHMA Product Standards Section C, Door Controls (Closers).“ ANSI approval was secured under the Canvass Method. BHMA was accredited on 21
8、 March 1983 by ANSI as a sponsor using the Canvass Method. Copyright Builders Hardware Manufacturers Association Inc. Provided by IHS under license with BHMA Licensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 01:31:06 MDTNo reproduction or networking permitted without lice
9、nse from IHS -,-,- 3 FOREWORD (This Foreword is not a part of ANSI/BHMA A156.14) The general classification of builders hardware includes a wide variety of items which are divided into several categories. To recognize this diversity, a sectional classification system has been established. Sliding an
10、d Folding Door Hardware is one such section and this Standard is the result of the collective efforts of members of the Builders Hardware Manufacturers Association, Inc., who manufacture this product. The total Product Standards effort is, therefore, a collection of sections, each covering a specifi
11、c category of items. Performance tests and, where it has been necessary, dimensional requirements have been established to insure safety, security and stability to which the public is entitled. There are no restrictions on design, except for those dimensional requirements imposed for the reasons giv
12、en above. It is also required that some hardware items fit certain specified cutout dimensions. The BHMA recognizes that errors will be found, items will become obsolete, and new products, methods and materials will be developed. With this in mind, the Association plans to update, correct and revise
13、 these Standards on a regular basis. In most cases, products have been described in grade levels related to performance. Grade classifications indicate levels only within their own category. Choice of grades and specific products are made on the basis of utility, aesthetics, security objectives and
14、end use desired. The BHMA numbers and pictorials which indicate types of hardware do not necessarily identify size, finish, or material and are not intended to be used without necessary supplementary information. Individual manufacturers catalogs are consulted. Copyright Builders Hardware Manufactur
15、ers Association Inc. Provided by IHS under license with BHMA Licensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 01:31:06 MDTNo reproduction or networking permitted without license from IHS -,-,- 4 TABLE OF CONTENTS 1. SCOPE .5 2. DEFINITIONS .5 3. TEST PROCEDURES.6 6. FOLD
16、ING DOORS10 7. FINISH TESTS (APPLICABLE TO ALL DOOR TYPES) .12 8. TYPICAL ILLUSTRATIONS AND IDENTIFYING TYPE NUMBERS.14 9. EXPLANATION OF IDENTIFYING TYPE NUMBERS .25 APPENDIX A (NOT A PART OF A156.14)27 Copyright Builders Hardware Manufacturers Association Inc. Provided by IHS under license with BH
17、MA Licensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 07/30/2008 01:31:06 MDTNo reproduction or networking permitted without license from IHS -,-,- 5 1. SCOPE 1.1 This Standard establishes requirements for Sliding and Folding Door Hardware. Cycle tests, abuse, durability static load,
18、 smoothness, static friction, kinetic friction and finish tests are included. Hardware for light to very heavy doors is covered including both residential and industrial applications. 1.2 Fire doors equipped with sliding door hardware shall successfully pass the requirements of ANSI/UL 10B or 10C. A
19、NSI/UL 14B specifies requirements for sliding door hardware used on sliding type fire doors. 1.3 Tests described in this Standard are performed under laboratory conditions. In actual usage, results vary because of installation, maintenance and environmental conditions. 1.4 All dimensions which do no
20、t carry specific tolerances or are not marked maximum or minimum are permitted to have nominal deviations. Dimensions are given in US units. SI unit (metric) equivalents given in parentheses are approximate. 1.5 ANSI Standards referenced in this Standard are available from the BHMA website or the A
21、merican National Standards Institute, 11 West 42nd Street, New York, NY 10036. 2. DEFINITIONS 2.1 Aligner A component added to a 4 door bifold set to keep the leading edge of doors flush when closed. 2.2 Bow Handle A pull for use on heavy doors. 2.3 Bumper Shoe A protection plate for the bottom edge
22、 of a door where it hits a stop. 2.4 Cane Bolt An L shaped rod held by guides which fixes a door in a closed or open position. 2.5 Chain Bolt See Spring Bolt. 2.6 Cremone Bolt Rods held by guides and controlled by a knob or lever. The rods project into members above and below a door. 2.7 Edge Pull A
23、 pull inserted into the edge of a sliding door. 2.8 Flush Pull A pull mortised into the face of a door. 2.9 Foot Bolt A bolt projected with ones foot and released against a spring loaded trigger mechanism. Fixes a door in a closed or open position. 2.10 Guide A device used to control lateral movemen
24、t of a sliding door. 2.11 Hanger Rollers with a connection to a door which suspend the door and allow it to travel in a track. 2.12 Heavy Sliding Door In this Standard, heavy sliding doors are intended to include those weighing over 240 lbs (109 kg) and generally used for industrial applications. 2.
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BHMA A156 14 2007
链接地址:https://www.31doc.com/p-3730209.html