ATS-5200.016-2005.pdf
《ATS-5200.016-2005.pdf》由会员分享,可在线阅读,更多相关《ATS-5200.016-2005.pdf(13页珍藏版)》请在三一文库上搜索。
1、ATS 5200.0162005 Australian Technical Specification Technical Specification for plumbing and drainage products Part 016: Cistern inlet valves ATS 5200.0162005 Accessed by TAFE QUEENSLAND INSTITUTES on 16 Nov 2007 This Australian Technical Specification was prepared by Committee WS-031, Technical Pro
2、cedures for Plumbing and Drainage Products Certification. It was approved on behalf of the Council of Standards Australia on 8 October 2004. This Technial Specification was published on 6 January 2005. The following are represented on Committee WS-031: AUSTAP Australian Electrical and Electronic Man
3、ufacturers Association Australian Industry Group CSIRO Manufacturing and Infrastructure Technology Certification Interests (Australia) Consumer Electronics Suppliers Association Copper Development CentreAustralia Gas Appliances and Services Association Master Plumbers Australia Master Plumbers and M
4、echanical Services Association of Australia Master Plumbers, Gasfitters and Drainlayers New Zealand National Fire Industry Association New Zealand Water & Waste Association Plastics Industry Pipe Association of Australia Plumbing Industry Commission South Australian Water Corporation Water Services
5、Association of Australia Keeping Standards up-to-date Standards are living documents which reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards m
6、ay also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased. Detailed information about Standards can be found by visiting the Standards Web Shop at .au and
7、looking up the relevant Standard in the on-line catalogue. Alternatively, the printed Catalogue provides information current at 1 January each year, and the monthly magazine, The Global Standard, has a full listing of revisions and amendments published each month. Australian StandardsTM and other pr
8、oducts and services developed by Standards Australia are published and distributed under contract by SAI Global, which operates the Standards Web Shop. We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies
9、 or ambiguities. Contact us via email at mailstandards.org.au, or write to the Chief Executive, Standards Australia, GPO Box 5420, Sydney, NSW 2001. Accessed by TAFE QUEENSLAND INSTITUTES on 16 Nov 2007 ATS 5200.0162005 Australian Technical Specification Technical Specification for plumbing and drai
10、nage products Part 016: Cistern inlet valves First published as ATS 5200.0162005. COPYRIGHT Standards Australia All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of t
11、he publisher. Published by Standards Australia GPO Box 5420, Sydney, NSW 2001, Australia ISBN 0 7337 6425 8 Accessed by TAFE QUEENSLAND INSTITUTES on 16 Nov 2007 ATS 5200.0162005 2 PREFACE This Technical Specification was prepared by the Joint Standards Australia/Standards New Zealand Committee WS-0
12、31, Technical Procedures for Plumbing and Drainage Products Certification. The objective of this Technical Specification is to provide writers of technical specifications for plumbing and drainage products with guidance and specific requirements for plumbing and drainage products to enable product c
13、ertification in accordance with the requirements of the Plumbing Code of Australia (PCA). Technical Specifications will stay current until converted into an Australian Standard, with the objective of converting within two (2) years of the approval date by the National Plumbing Regulatory Forum (NPRF
14、). The word VOID set against a clause indicates that the clause is not used in this Technical Specification. The inclusion of this word allows for the use of a common clause numbering system for the Plumbing and Drainage Technical Specification. The test protocol and information in this Specificatio
15、n was arranged by committee members to meet the authorization requirements given in the Plumbing Code of Australia. Accessed by TAFE QUEENSLAND INSTITUTES on 16 Nov 2007 3 ATS 5200.0162005 CONTENTS Page 1 SCOPE4 2 APPLICATION .4 3 REFERENCED DOCUMENTS4 4 DEFINITIONS4 5 MATERIALS5 6 MARKING .5 7 VOID
16、5 8 DESIGN5 9 PERFORMANCE REQUIREMENTS AND TEST METHODS.6 10 VOID6 11 PRODUCT DOCUMENTATION.6 APPENDIX A MEANS OF DEMONSTRATING COMPLIANCE WITH THIS TECHNICAL SPECIFICATION7 Accessed by TAFE QUEENSLAND INSTITUTES on 16 Nov 2007 ATS 5200.0162005 4 Standards Australia .au STANDARDS AUSTRALIA Australia
17、n Technical Specification Technical Specification for plumbing and drainage products Part 016: Cistern inlet valves 1 SCOPE This Technical Specification applies to cistern inlet valves that are intended for replacement use in flushing cisterns of the types specified in AS 1172.2. 2 APPLICATION Appen
18、dix A sets out the means by which compliance with the Specification shall be demonstrated by a manufacturer for the purpose of product certification (See Appendix A). 3 REFERENCED DOCUMENTS The following documents are referred to in this Specification: AS 1172 Water closet (WC) pans of 6/3 L capacit
19、y or proven equivalent 1172.2 Part 2: Cisterns 1432 Copper tubes for plumbing, gasfitting and drainage applications 1565 Copper and copper alloysIngots and castings 1572 Copper and copper alloysSeamless tubes for engineering purposes 2136 Method for detecting the susceptibility of copper and its all
20、oys to stress corrosion cracking using the mercurous nitrate test 2345 Dezincification resistance of copper alloys 2738 Copper and copper alloysCompositions and designations of refinery products, wrought products, ingots and castings 3688 Water supplyCopper and copper alloy body compression and capi
21、llary fittings and threaded-end connectors AS/NZS 1567 Copper and copper alloysWrought rods, bars and sections 1568 Copper and copper alloysForging stock and forgings 3500 Plumbing and drainage 3500.0 Part 0: Glossary of terms 3500.1 Part 1: Water services 4020 Testing of products for use in contact
22、 with drinking water 4 DEFINITIONS For the purpose of this Australian Technical Specification, the definitions given in AS/NZS 3500.0 and AS 1172.2 apply. Accessed by TAFE QUEENSLAND INSTITUTES on 16 Nov 2007 5 ATS 5200.0162005 .au Standards Australia 5 MATERIALS 5.1 Copper Copper shall comply with
23、the following: (a)Wrought products shall comply with AS 2738. (b)Tubular components shall comply with AS 1432. 5.2 Copper alloy Copper alloy shall comply with the following: (a)Castings AS 1565 or capable of passing the requirements of Clause 5.3 provided that the alloy contains not less than 58% co
24、pper and not more than 1% aluminium. (b)Hot pressings AS/NZS 1568. (c)Rod for machined parts AS/NZS 1567. (d)Tubular components Copper alloy tube shall comply with AS 1572 alloy designation C26130. Where bent or stamped in the fabrication process, the tube shall be sufficiently stress-relieved so th
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ATS 5200.016 2005
链接地址:https://www.31doc.com/p-3732446.html