BS-2782-6-METHOD-621D-1978 ISO-1068-1975.pdf
《BS-2782-6-METHOD-621D-1978 ISO-1068-1975.pdf》由会员分享,可在线阅读,更多相关《BS-2782-6-METHOD-621D-1978 ISO-1068-1975.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD CONFIRMED JULY 1989 BS 2782-6: Method 621D: 1978 ISO 1068:1975 Methods of testing Plastics Part 6: Dimensional properties Method 621D: Determination of compacted apparent bulk density of PVC resins ISO title: Plastics PVC resins Determination of compacted apparent bulk density IMPOR
2、TANT NOTE. Before reading this method, it is essential to read the foreword, general introduction and instructions to BS 2782, issued separately. UDC 678.5/.8:678.01:542.3:531.755.22:678.743.24 Licensed Copy: London South Bank University, London South Bank University, Tue Dec 12 08:46:08 GMT+00:00 2
3、006, Uncontrolled Copy, (c) BSI BS 2782-6:Method 621D:1978 This British Standard, having been prepared under the direction of Plastics Standards Committee, was published under the authority of the Executive Board on 28 February 1978 BSI 11-1999 The following BSI references relate to the work on this
4、 standard: Committee reference PLC/17 Draft for comment 77/50307 DC ISBN 0 580 10029 4 National foreword This method is identical with ISO 1068 “Plastics PVC resins Determination of compacted apparent bulk density” which has been prepared by ISO/TC 61, Plastics. Terminology and conventions. The text
5、 of the International Standard has been approved as suitable for publication, without deviation, as a British Standard. Some terminology and certain conventions are not identical with those used in British Standards; attention is especially drawn to the following. The comma has been used throughout
6、as a decimal marker. In British Standards it is current practice to use a full point (on the baseline) as the decimal marker. Where the words “International Standard” appear, referring to this standard, they should be interpreted as “British Standard”. Cross-reference. For the following reference to
7、 an International Standard given in the text, there is a corresponding British Standard; this is given below: WARNING NOTE. This method, which is identical with ISO 1068, does not necessarily detail all the precautions necessary to meet the requirements of the Health and Safety at Work etc. Act 1974
8、. Attention should be paid to any necessary safety precautions, and the method should only be operated by trained personnel. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance
9、 with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorpora
10、ted. This will be indicated in the amendment table on the inside front cover. Reference to International Standard Corresponding British Standard ISO 60:1977aBS 2782:Method 621A:1978 Apparent density of moulding material that can be poured from a funnel (identical) a Since the publication of ISO 1068
11、, ISO/R 60 (referred to in clause 1) has been superseded by ISO 60 “Plastics Determination of apparent density of material that can be poured from a specified funnel”. Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank Uni
12、versity, Tue Dec 12 08:46:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 2782-6:Method 621D:1978 BSI 11-1999i Contents Page National forewordInside front cover 1Scope and field of application1 2Principle1 3Apparatus1 4Procedure1 5Expression of results1 6Test report1 Figure Test apparatus2 Licensed
13、 Copy: London South Bank University, London South Bank University, Tue Dec 12 08:46:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: London South Bank University, London South Bank University, Tue Dec 12 08:46:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 2782-6:Method 621D:1
14、978 BSI 11-19991 1 Scope and field of application This International Standard specifies a method for the determination of the compacted apparent bulk density of PVC resins. NOTEThe non-compacted apparent bulk density may be determined according to ISO/R 60, Determination of apparent density of mould
15、ing material that can be poured from a specified funnel. 2 Principle Placing a known quantity of PVC resin in a precision graduated cylinder and submitting to shaking under given conditions. Calculation of the compacted apparent bulk density from the mass of the resin and its volume after compaction
16、. 3 Apparatus 3.1 Shaking machine, giving 100 to 250 falls per minute from a height of 3 0,2 mm, as shown in the Figure. The cylinder holder shall have a mass of 450 20 g. 3.2 Precision graduated glass measuring cylinder, 250 ml capacity, graduated in 2 ml and with a non-graduated portion of at leas
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-2782-6-METHOD-621D-1978 ISO-1068-1975 BS 2782 METHOD 621 1978 ISO 1068 1975
链接地址:https://www.31doc.com/p-3732766.html