AS-2332-2003.pdf
《AS-2332-2003.pdf》由会员分享,可在线阅读,更多相关《AS-2332-2003.pdf(41页珍藏版)》请在三一文库上搜索。
1、AS 23322003 Australian Standard Slide fasteners AS 2332 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 06 May 2008 This Australian Standard was prepared by Committee TX-018, Specifications for Textile Furnishings. It was approved on behalf of the Council of Standards Australia on 10 September 2003 and
2、 published on 7 November 2003. The following are represented on Committee TX-018: AWTA Textile Testing Australian Chamber of Commerce and Industry Australian Retailers Association Australian Wool Processors Council Certification Interests Consumer Affairs Victoria Drycleaning Institute of Australia
3、Furnishers Society of Victoria National Council of Women of Australia Society of Dyers and Colourists of Australia and New Zealand Soft Furnishings Industry Association of Australia Textile Distributors Association Keeping Standards up-to-date Standards are living documents which reflect progress in
4、 science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which
5、should include any amendments which may have been published since the Standard was purchased. Detailed information about Standards can be found by visiting the Standards Australia web site at .au and looking up the relevant Standard in the on-line catalogue. Alternatively, the printed Catalogue prov
6、ides information current at 1 January each year, and the monthly magazine, The Global Standard, has a full listing of revisions and amendments published each month. We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent
7、 inaccuracies or ambiguities. Contact us via email at .au, or write to the Chief Executive, Standards Australia International Ltd, GPO Box 5420, Sydney, NSW 2001. This Standard was issued in draft form for comment as DR 02532. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 06 May 2008 AS 23322003 Aust
8、ralian Standard Slide fasteners Originated as AS 23321980. Second edition 2003. COPYRIGHT Standards Australia International All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written per
9、mission of the publisher. Published by Standards Australia International Ltd GPO Box 5420, Sydney, NSW 2001, Australia ISBN 0 7337 5521 6 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 06 May 2008 AS 23322003 2 PREFACE This Standard was prepared by the Standards Australia Committee TX-018, Specificati
10、ons for Textile Furnishings to supersede AS 23321980. This Standard is based on but not equivalent to BS 30841992, Specification for slide fasteners but reference was also made to the Japanese Standard, JIS S 3015:1993, Slide fasteners and the US Federal Specification FEDSPEC V-F-106F:1998, Fastener
11、, slide, interlocking and results of testing of slide fasteners which had given further insight into failures and the need for tougher requirements. Slide fasteners are classified by their chain width with performance classes ranging from ultra light to ultra heavy. Ultra heavy is an added class in
12、this edition of the Standard. The secondary method of determining class is by the end use. The terms normative and informative have been used in this Standard to define the application of the appendix to which they apply. A normative appendix is an integral part of a Standard, whereas an informative
13、 appendix is only for information and guidance. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 06 May 2008 3 AS 23322003 CONTENTS Page 1 SCOPE4 2 REFERENCED DOCUMENTS4 3 DEFINITIONS5 4 SAFETY .6 5 CLASSIFICATION.6 6 PERFORMANCE REQUIREMENTS OF FASTENERS9 7 MARKING11 APPENDICES A PULLER ATTACHMENT TEST
14、 (TEST 1) 12 B CLOSED-END TEST (TEST 2) 14 C TOP-STOP TEST (TEST 3).16 D OPEN END FASTENER BOX TEST (TEST 4)18 E RECIPROCATING TEST (TEST 5)20 F LATERAL STRENGTH TEST (TEST 6)25 G LATERAL STRENGTH OF OPEN-END ATTACHMENT TEST (TEST 7)27 H SLIDER LOCKING TEST (TEST 8).29 I METHOD OF TESTING SECURITY O
15、F SEPARATE ELEMENT FASTENERS LATERALLY (TEST 9)31 J METHOD OF TESTING SECURITY OF SEPARATE ELEMENT FASTENERS LONGITUDINALLY (TEST 10).33 K GUIDANCE ON FACTORS TO BE TAKEN INTO CONSIDERATION WHEN SPECIFYING SLIDE FASTENERS35 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 06 May 2008 AS 23322003 4 Stand
16、ards Australia .au STANDARDS AUSTRALIA Australian Standard Slide fasteners 1 SCOPE This Standard specifies performance levels for the following characteristics of slide fasteners made from interlocking components mounted on textile tapes: strengths of puller attachment, closed-end, top-stop, open en
17、d fastener box, reciprocating mechanism, closed fastener when extended laterally, open end attachment when extended laterally, slider lock and security of separate element fasteners laterally and longitudinally. Tests for quantifying these properties are given in the Appendices A to J. In addition,
18、performance levels are specified for colourfastness to washing, drycleaning, water, and for dimensional change to washing and drycleaning. NOTE: Guidance on factors to be considered when specifying slide fasteners is given in Appendix K. Properties specific to applications such as aeronautics and fa
19、steners of complicated structure such as three-way and double-pull are not included within the scope of this Standard. 2 REFERENCED DOCUMENTS The following documents are referred to in this Standard: AS 2001 Methods of test for textiles 2001.4.B02 Part 4.B02: Colourfastness testsColourfastness to ar
20、tificial light: Xenon arc fading lamp test (ISO 105-B02:1994, MOD) 2001.4.E01 Part 4.E01: Colourfastness testsColourfastness to water 2001.4.3 Part 4.3: Colourfastness testsDetermination of colourfastness to rubbing 2001.4.15 Part 4.15: Colourfastness testsDetermination of colourfastness to washing
21、2001.4.16 Part 4.16: Colourfastness testsDetermination of colourfastness to dry cleaning solvents 2001.4.21 Part 4.21: Colourfastness testsDetermination of colourfastness to light using an artificial light source (mercury vapour, tungsten filament, internally phosphor-coated lamp) 2001.5.4 Part 5.4:
22、 Dimensional changeDetermination of dimensional change in laundering of textile fabrics and garmentsAutomatic machine method 2001.5.7 Part 5.7: Dimensional changeDetermination of dimensional change on dry cleaning in perchloroethylene excluding finishingMachine method 2193 Calibration and classifica
23、tion of force-measuring systems ISO 105 TextilesTests for colour fastness 105-B02 Part B02: Colour fastness to artificial light: Xenon arc fading lamp test 105-C03 Part C03: Colour fastness to washing: Test 3 105-D01 Part D01: Colour fastness to dry cleaning 105-E01 Part E01: Colour fastness to wate
24、r 105-X12 Part X12: Colour fastness to rubbing Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 06 May 2008 5 AS 23322003 .au Standards Australia ISO 3175 TextilesDry cleaning and finishing 3175-1 Part 1: Method for assessing the cleanability of textiles and garments 6330 TextilesDomestic washing and dr
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AS 2332 2003
链接地址:https://www.31doc.com/p-3732900.html