AS-5200.000-2006.pdf
《AS-5200.000-2006.pdf》由会员分享,可在线阅读,更多相关《AS-5200.000-2006.pdf(33页珍藏版)》请在三一文库上搜索。
1、AS 5200.0002006 Australian Standard Technical specification for plumbing and drainage products Part 000: Procedures for certification of plumbing and drainage products AS 5200.0002006 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 26 Aug 2008 This Australian Standard was prepared by Committee WS-031,
2、Technical Procedures for Plumbing and Drainage Products Authorization. It was approved on behalf of the Council of Standards Australia on 30 May 2006. This Standard was published on 23 June 2006. The following are represented on Committee WS-031: AUSTAP Australian Electrical and Electronic Manufactu
3、rers Association Australian Industry Group Australian Stainless Steel Development Association Building Officials Institute of New Zealand Building Research Association of New Zealand Certification Interests (Australia) Copper Development CentreAustralia Master Plumbers, Gasfitters and Drainlayers Ne
4、w Zealand National Fire Industry Association Plastics Industry Pipe Association of Australia Plumbing Industry Commission South Australian Water Corporation Water Services Association of Australia Keeping Standards up-to-date Standards are living documents which reflect progress in science, technolo
5、gy and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any
6、 amendments which may have been published since the Standard was purchased. Detailed information about Standards can be found by visiting the Standards Web Shop at .au and looking up the relevant Standard in the on-line catalogue. Alternatively, the printed Catalogue provides information current at
7、1 January each year, and the monthly magazine, The Global Standard, has a full listing of revisions and amendments published each month. Australian StandardsTM and other products and services developed by Standards Australia are published and distributed under contract by SAI Global, which operates
8、the Standards Web Shop. We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Contact us via email at mailstandards.org.au, or write to the Chief Executive, Standards Australia, GPO Box 476
9、, Sydney, NSW 2001. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 26 Aug 2008 AS 5200.0002006 Australian Standard Technical specification for plumbing and drainage products Part 000: Procedures for certification of plumbing and drainage products Originated as MP 521988. Previous edition 2005. Revised
10、 and redesignated as AS 5200.0002005. Second edition 2006. COPYRIGHT Standards Australia All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher. Published
11、 by Standards Australia GPO Box 476, Sydney, NSW 2001, Australia ISBN 0 7337 7535 7 Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 26 Aug 2008 AS 5200.0002006 2 PREFACE This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee WS-031, Technical Procedures for Plumbing
12、 and Drainage Products Authorization, and the National Plumbing Regulators Forum to supersede AS 5200.000 2005, Technical Specification for plumbing and drainage products, Part 000: Procedures for certification of plumbing and drainage. The objective of this revision is to list new Australian Techni
13、cal Specifications and Standards approved by the NPRF for inclusion in the WaterMark Scheme and to ensure compliance of the Australian Technical Specifications with the Plumbing Code of Australia. The objective of this Standard is to provide an outline of the WaterMark Certification Scheme (WMCS), w
14、hich is based on a single mark, WaterMark with two levels of certification. The WMCS replaced the previous National Certification of Plumbing and Drainage Products Scheme (known as the NCPDP Scheme), which incorporated StandardsMark, WaterMark and TypeTest Mark. The scheme design conforms to the req
15、uirements of AS ISO/IEC 17030, Conformity assessmentGeneral requirements for third-party marks of conformity. The new WaterMark scheme facilitates the certification and authorization of plumbing and drainage products in accordance with Part G1 of the Plumbing Code of Australia. Schedule 5 lists the
16、specifications that can be used certify products to WaterMark Level 1 or Level 2. The terms normative and informative have been used in this Standard to define the application of the appendix to which they apply. A normative appendix is an integral part of a Standard, whereas an informative appendix
17、 is for information and guidance only. Accessed by UNIVERSITY OF SOUTH AUSTRALIA on 26 Aug 2008 3 AS 5200.0002006 CONTENTS Page 1 SCOPE AND GENERAL5 2 DEFINITIONS 5 3 MARKING .6 4 CERTIFICATION.6 5 SCHEDULE OF SPECIFICATIONS 10 6 PRODUCTS USED IN URBAN WATER INDUSTRY NETWORK INFRASTRUCTURE 16 APPEND
18、ICES A REFERENCED STANDARDS SPECIFICATIONS . 17 B A GUIDE TO THE USE OF WATERMARK ON PLUMBING AND DRAINAGE PRODUCTS SUPPLIED UNDER THE WMCS. 22 C A GUIDE TO THE PROCESS OF CERTIFICATION OF THOSE PRODUCTS THAT ARE NOT LISTED BUT REQUIRE CERTIFICATION . 25 D PRODUCTS OUTSIDE THE WATERMARK SCHEME. 28 A
19、ccessed by UNIVERSITY OF SOUTH AUSTRALIA on 26 Aug 2008 AS 5200.0002006 4 INTRODUCTION Part G1 of the Plumbing Code of Australia sets out objectives, procedures and processes for the certification and authorization of plumbing and drainage materials and products so that they may be authorized for us
20、e in plumbing and drainage installations. This Standard supports the certification process by providing a detailed list of specifications for plumbing and drainage products nominated in Table A2.1 of the Code. This Standard supports the WaterMark Certification Scheme (WMCS) by nominating appropriate
21、 Standards and, where these Standards do not exist, Australian Technical Specifications (ATS) for plumbing and drainage products. International Standards Internationally recognized Standards or relevant parts thereof may be recognized as a means to accelerate the acceptance of products into the WMCS
22、. Referenced Standards Due to the ever-changing status of referenced Standards, the year of publication of the respective Standard is not stated. WaterMark WaterMark is a registered certification Trademark owned by Standards Australia, the rules of which are set out in Rules for the WaterMark Certif
23、ication Trademarks. Product database The WaterMark Product Database will be available at WaterMark.standards.org.au. Transitional period A transitional period will be available, which will enable manufacturers to modify marking, certification level or the specification under the revised WMCS. It is
24、anticipated that this transitional period will not exceed 5 years from the date of publication of this Standard. WaterMark levels The WMCS provides for two levels of certification: WaterMark Level 1requires that products comply with a specific Australian or International Standard or other suitable p
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AS 5200.000 2006
链接地址:https://www.31doc.com/p-3732924.html