BHMA-A156.6-2005 p.pdf
《BHMA-A156.6-2005 p.pdf》由会员分享,可在线阅读,更多相关《BHMA-A156.6-2005 p.pdf(16页珍藏版)》请在三一文库上搜索。
1、ANSI/BHMA A156.6-2005 Revision of ANSI/BHMA A156.6-2001 AMERICAN NATIONAL STANDARD FOR ARCHITECTURAL DOOR TRIM SPONSOR BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. Approved September 20, 2005 AMERICAN NATIONAL STANDARDS INSTITUTE, INC. 2 AMERICAN NATIONAL STANDARD An American National Standard
2、implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he ha
3、s approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. CAUTION NOTICE: This American Natio
4、nal Standard is permitted to be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise or withdraw this standard no later than five years from the date of publication. Purchasers of American National Standards re
5、ceive current information on all standards by calling or writing the American National Standards Institute. Published by BUILDERS HARDWARE MANUFACTURERS ASSOCIATION, INC. 355 Lexington Avenue, New York, New York 10017 Copyright 2005 by the Builders Hardware Manufacturers Association, Inc. Not to be
6、 reproduced without specific authorization from BHMA Printed in the USA This standard was first published December 1969 by the Builders Hardware Manufacturers Association, Inc. It was entitled, “Standard 1001 BHMA Product Standards Section J, Architectural Door Trim.” This Standard was approved by A
7、NSI under the Canvass Method. BHMA was accredited on 21 March 1983 as a sponsor using the Canvass Method. 3 FOREWORD (This Foreword is not a part of ANSI/BHMA A156.6) The general classification of builders hardware includes a wide variety of items which are divided into several categories. To recogn
8、ize this diversity, a sectional classification system has been established. Architectural Door Trim is one such section and this Standard is a result of the collective efforts of members of the Builders Hardware Manufacturers Association, Inc. who manufacture this product. The total Product Standard
9、s effort is, therefore, a collection of sections, each covering a specific category of items. Performance tests and, where it has been necessary, material and dimensional requirements have been established to insure safety and stability to which the public is entitled. There are no restrictions on d
10、esign except for those dimensional requirements imposed for reasons given above. The BHMA recognizes that errors will be found, items will become obsolete, and new products, methods and materials will be developed. With this in mind, the Association plans to update, correct and revise these Standard
11、s on a regular basis. The BHMA numbers which indicate types and functions of hardware do not identify size, finish, material or design and are not intended to be used without necessary supplementary information. Users of this Standard who require a specific design for a product type should describe
12、it, using generic terms or the manufacturers name and description of the product desired. ORDERING INFORMATION BHMA standards, publications, and matchplates can be ordered at: - Search entire catalog, order printed or electronic versions, and download electronic versions right to your computer. Cal
13、l our Fulfillment Partner, Techstreet, at: Toll-free (800) 699-9277 (U.S. and Canada) Ph. (734) 913-3930 Fax (734) 913-3946 E-mail: Send mail to: BHMA c/o Techstreet 777 E. Eisenhower Parkway Ann Arbor, MI 48108 USA -,-,- 4 TABLE OF CONTENTS 1. SCOPE.5 2. DEFINITIONS.5 3. GENERAL.5 4. PRODUCT CATEG
14、ORY J100 - DOOR PROTECTION PLATES .7 5. PRODUCT CATEGORY J200 - DOOR EDGINGS 8 6. PRODUCT CATEGORY J300 - PUSH PLATES 9 7. PRODUCT CATEGORY J400 - DOOR PULLS AND PUSH/PULL UNITS.11 8. PRODUCT CATEGORY J500 - PUSH BARS AND PULL BARS.13 9. FINISH TESTS14 APPENDIX A 16 -,-,- 5 1. SCOPE 1.1 This Standar
15、d contains requirements for door protection plates, door edgings, push plates, door pulls, push bars, and pull bars. Included are strength and finish tests, and dimensional and material criteria. 1.2 Tests described in this Standard are performed under laboratory conditions. In actual usage, results
16、 vary because of installation, maintenance and environmental conditions. 2. DEFINITIONS 2.1 Door Edging: Protective material applied to the edge of a door. 2.2 Door Protection Plate: Protective material applied to the face of a door. 2.3 Door Pull: A device applied to the face of a door and when gra
17、sped permits the user to pull a door open. 2.4 Kick Plate: A protective plate applied to the lower part of the door surface on the closing side of the door. 2.5 Mop Plate: A protective plate applied to the lower part of the door surface on the opening side of the door. 2.6 Pull Plate: An assembly co
18、nsisting of a door pull with a protective material positioned between the pull and face of a door. 2.7 Pull Bar: A device extending across or vertically on a door and when grasped permits the user to pull a door open. 2.8 Push Bar: Similar to pull bar but used for pushing a door open. 2.9 Push Plate
19、: Material applied to the surface of a door and located where a user is to push on a door to open it. 2.10 Push/Pull Unit: A non-latching device applied to the face of a door and offering suitable surfaces for either a pushing or pulling operation of the door. 2.11 Stretcher Plate: A protective plat
20、e applied to the middle part of the door surface on either side of the door. 3. GENERAL 3.1 Reference to other Standards ANSI Standards referenced in this Standard are available from: American National Standards Institute, Inc., 11 West 42nd Street, New York, NY 10036 or . 3.2 Dimensions All dimensi
21、ons are given in US units with approximate SI (metric) conversions. Where plus or minus tolerances are not given, values are permitted to be correspondingly reduced or exceeded at the option of the manufacturer within the functional limitations of the product. 3.3 Workmanship Products meeting this S
22、tandard shall be free of imperfections and defects affecting appearance, durability and service. 6 3.4 Materials Materials to be used are listed in the product category description. Experience has shown these will provide a serviceable product. Where brass is mentioned, reference is to mean yellow b
23、rass, red brass or 90% commercial bronze. Metal used shall be determined by the finish (see 3.5) specified for the product. Wherever stainless steel is mentioned, reference is to mean 300 series (chrome nickel) stainless steel. 3.5 Finish Finishes shall conform to the finish test values in this Stan
24、dard for all applicable products. Appearance and test procedures shall conform to ANSI/BHMA A156.18-2000 for Materials and Finishes. All visible parts when the product is installed shall match subject to the limitations stated under the product category and to natural variations of those finishes fa
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BHMA-A156.6-2005 BHMA A156 2005
链接地址:https://www.31doc.com/p-3732941.html