BS-7007-3-1988 ISO-8366-1987.pdf
《BS-7007-3-1988 ISO-8366-1987.pdf》由会员分享,可在线阅读,更多相关《BS-7007-3-1988 ISO-8366-1987.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS 7007-3: 1988 ISO 8366:1987 Abrasive products Part 3: Specification for dimensional tolerances on non-standard coated abrasive products ISO title: Coated abrasive products Dimensional tolerances on non-standard conversions UDC 621.922.025:62 254.63:62 231.322.5 (083.3) Licensed Co
2、py: London South Bank University, London South Bank University, Fri Dec 08 11:35:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7007-3:1988 This British Standard, having been prepared under the direction of the Machine, Engineers and Hand Tool Standards Committee, was published under the authority
3、 of the Board of BSI and comes into effect on 30 September 1988 BSI 10-1999 The following BSI references relate to the work on this standard: Committee reference MTE/3 Draft for comment 86/72300 DC ISBN 0 580 16789 5 Committees responsible for this British Standard The preparation of this British St
4、andard was entrusted by the Machine, Engineers and Hand Tool Standards Committee (MTE/-) to Technical Committee MTE/3, upon which the following bodies were represented: Abrasive Industries Association Advanced Manufacturing Technology Research Institute British Paper and Board Industry Federation Co
5、ated Abrasives Manufacturers Association Electronic Components Industry Association Coopted member Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:35:07 GMT+00:00 2006, Uncontrolled Copy, (c) B
6、SI BS 7007-3:1988 BSI 10-1999i Contents Page Committees responsibleInside front cover National forewordii 1Scope and field of application1 2References1 3Measurement conditions1 4Dimensional tolerances on discs1 5Dimensional tolerances on belts1 6Dimensional tolerances on other cross-sections2 Table
7、11 Table 21 Table 32 Publications referred toInside back cover Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:35:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7007-3:1988 ii BSI 10-1999 National foreword This Part of BS 7007 has been prepared under the di
8、rection of the Machine, Engineers and Hand Tool Standards Committee. It is identical with ISO 8366:1987 “Coated abrasive products Dimensional tolerances on non-standard conversions”, published by the International Organization for Standardization (ISO). The other Parts of BS 7007 are as follows: Par
9、t 1: Specification for dimensions and designation of truncated cone abrasive products; Part 2: Specification for designation and dimensions of coated abrasive flap wheels with shafts. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as
10、 a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. Wherever the words “International Standard” appear, referring to this standard, they should be read as “Part of BS 7
11、007”. Cross-references. The Technical Committee has reviewed the provisions of ISO 554 and ISO 3017, to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. The references to ISO 1929 and ISO 2235 are included for information only.
12、A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises
13、a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London Sou
14、th Bank University, London South Bank University, Fri Dec 08 11:35:07 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7007-3:1988 BSI 10-19991 1 Scope and field of application This International Standard lays down the dimensional tolerances on non-standard discs, belts and other cross-sections for coa
15、ted abrasive products. The dimensional tolerances on standardized products are specified in ISO 1929, ISO 2235 and ISO 3017. 2 References ISO 554, Standard atmospheres for conditioning and/or testing Specifications. ISO 1929, Abrasive belts Designation, dimensions and tolerances. ISO 2235, Abrasive
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-7007-3-1988 ISO-8366-1987 BS 7007 1988 ISO 8366 1987
链接地址:https://www.31doc.com/p-3735709.html