BS-7007-2-1994 ISO-3919-1993.pdf
《BS-7007-2-1994 ISO-3919-1993.pdf》由会员分享,可在线阅读,更多相关《BS-7007-2-1994 ISO-3919-1993.pdf(6页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS 7007-2: 1994 ISO 3919:1993 Abrasive products Part 2: Specification for designation and dimensions of coated abrasive flap wheels with shafts UDC 621.922.6 Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:39:29 GMT+00:00 2006, Uncontrolled C
2、opy, (c) BSI BS 7007-2:1994 This British Standard, having been prepared under the direction of the Machine, Engineers and Hand Tools Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 February 1994 BSI 11-1999 First published September 19
3、88 Second edition February 1994 The following BSI references relate to the work on this standard: Committee reference MTE/3 Draft for comment 92/74219 DC ISBN 0 580 22786 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Machine, Enginee
4、rs and Hand Tools Standards Policy Committee (MTE/-) to Technical Committee MTE/3, upon which the following bodies were represented: Abrasive Industries Association Advanced Manufacturing Technology Research Institute British Paper and Board Industry Federation Coated Abrasives Manufacturers Associa
5、tion Amendments issued since publication Amd. No.DateComments Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:39:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7007-2:1994 BSI 11-1999i Contents Page Committees responsibleInside front cover National foreword
6、ii 1Scope1 2Dimensions1 3Designation1 Figure 11 Table 11 Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:39:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7007-2:1994 ii BSI 11-1999 National foreword This Part of BS 7007 has been prepared under the directio
7、n of the Machine, Engineers and Hand Tools Standards Policy Committee. It is identical with ISO 3919:1993 Coated abrasives Flap wheels with shafts Dimensions and designation, published by the International Organization for Standardization (ISO), and in the development of which the United Kingdom pla
8、yed an active part. This Part of BS 7007 supersedes BS 7007-2:1988 which is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of i
9、tself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, page 1 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment
10、table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:39:29 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7007-2:1994 BSI 11-19991 1 Scope This International Standard specifies the dimensions, in millimetres, of flap wheels with sha
11、fts and their designation. 2 Dimensions See Figure 1 and Table 1. 3 Designation Flap wheels with shafts conforming to this International Standard shall be designated by a) “Flap wheel with shaft”; b) reference to this International Standard; c) the diameter of the flap wheel, D, in millimetres; d) t
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-7007-2-1994 ISO-3919-1993 BS 7007 1994 ISO 3919 1993
链接地址:https://www.31doc.com/p-3735723.html