BS-7568-30-1993 ISO-9448-9-1993.pdf
《BS-7568-30-1993 ISO-9448-9-1993.pdf》由会员分享,可在线阅读,更多相关《BS-7568-30-1993 ISO-9448-9-1993.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS 7568-30: 1993 ISO 9448-9: 1992 Press tools Part 30: Specification for guide bushes: form B, ball cage bushes, plain, type 2 UDC 621.979.07 Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:39:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS
2、7568-30:1993 This British Standard, having been prepared under the direction of the Machine, Engineers and Hand Tools Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 November 1993 BSI 10-1999 The following BSI references relate to the
3、work on this standard: Committee reference MTE/12 Draft for comment 91/73259 DC ISBN 0 580 22358 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Machine, Engineers and Hand Tools Standards Policy Committee (MTE/-) to Technical Committe
4、e MTE/12, upon which the following bodies were represented: Advanced Manufacturing Technology Research Institute Amalgamated Engineering Union Gauge and Tool Makers Association Coopted member Amendments issued since publication Amd. No.DateComments Licensed Copy: London South Bank University, London
5、 South Bank University, Fri Dec 08 11:39:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7568-30:1993 BSI 10-1999i Contents Page Committees responsibleInside front cover National forewordii 1Scope1 2Dimensions1 3Material and corresponding hardness1 4Designation1 Annex A (informative) BibliographyIn
6、side back cover Figure 11 Table 12 Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:39:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7568-30:1993 ii BSI 10-1999 National foreword This Part of BS 7568 has been prepared under the direction of the Machine, Eng
7、ineers and Hand Tools Standards Policy Committee. It is identical with ISO 9448-9:1992 Tools for pressing Guide bushes Part 9: Form B, ball cage bushes, plain, type 2, published by the International Organization for Standardization (ISO). A British Standard does not purport to include all the necess
8、ary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1
9、 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08
10、11:39:15 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7568-30:1993 BSI 10-19991 1 Scope This part of ISO 9448 specifies the main dimensions and tolerances, in millimetres, of guide bushes of form B, plain ball cage bushes, type 2, intended for use in press tools and to be mounted in the clamp plate
11、 by means of interference fit. It gives guidance on the materials, and specifies the hardness and the designation of bushes in accordance with this part of ISO 9448. 2 Dimensions See Figure 1 and Table 1. Details not stated, such as chamfers, radii, lubrication grooves, etc., are left to the manufac
12、turers discretion. 3 Material and corresponding hardness The material is left to the manufacturers discretion and the hardness shall be 60HRC. 4 Designation A guide bush in accordance with this part of ISO 9448 shall be designated by a) “Guide bush”; b) a reference to this part of ISO 9448; c) its f
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-7568-30-1993 ISO-9448-9-1993 BS 7568 30 1993 ISO 9448
链接地址:https://www.31doc.com/p-3735950.html