《BS-AU-209-0-1996.pdf》由会员分享,可在线阅读,更多相关《BS-AU-209-0-1996.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 209-0:1996 Vehicle security Part 0: Guide to the application of security devices/systems to vehicles Product code 00565035 Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 16:58:44 GMT+00:00 2006, Uncontrolled Copy, (c) BS
2、I BS AU 209-0:1996 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 January 1996 BSI 03-1999 The following BSI references relate to the work on this standard: Committe
3、e reference AUE/17 Draft for comment 94/708972 DC ISBN 0 580 24622 1 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee AUE/17, Vehicle security, upon which the following bodies were represented: Association of Car Fleet Ope
4、rators Automobile Association Automobile Glazing Executive British Security Industry Association Consumer Policy Committee of BSI Consumers Association Department of Trade and Industry (Vehicle Division) Department of Trasnport Freight Transport Association Home Office Ice (Ergonomics) Master Locksm
5、iths Association Metropolitan Police Motor Industry Research Association Road Haulage Association Ltd. Royal Automobile Club Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.DateComments Licensed Copy: London South Bank University, London South Bank Univ
6、ersity, Fri Dec 08 16:58:44 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 209-0:1996 BSI 03-1999i Contents Page Committees responsibleInside front cover Forewordii Introduction1 1Scope1 2Informative references1 3Vehicle perimeter security1 4Alarm on breach of perimeter security (BS 6803)2 5Securi
7、ty of in-car entertainment systems (BS AU 209-2)2 6Immobilization (BS AU 209-10)2 7Aiding the recovery of stolen vehicles2 8Assessing the security of a vehicle3 Table 1 Summary of benefits to be derived from various security devices4 List of referencesInside back cover Licensed Copy: London South Ba
8、nk University, London South Bank University, Fri Dec 08 16:58:44 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 209-0:1996 ii BSI 03-1999 Foreword This Part of BS AU 209 has been prepared by Technical Committee AUE/17 and primarily gives guidance on original equipment security systems that can be
9、fitted to mass production vehicles. Alarm systems that can be specified both as original and/or after sales equipment are subject to BS 6803. Other Parts of BS AU 209 are as follows: Part 1a: Specification for locking systems for passenger cars and car derived vehicles; Part 2: Specification for sec
10、urity systems against theft of in-car entertainment and communication purposes; Part 3: Specification for security marking of glazing for passenger cars and car derived vehicles; Part 4: Specification for security glazing for passenger cars and car derived vehicles; Part 5b: Specification for centra
11、l power locking systems for passenger cars and car derived vehicles; Part 6a: Specification for dead locking systems for passenger cars and car derived vehicles; Part 7: Specification for locking systems for goods vehicle drivers compartments. It is envisaged that the following Parts will be publish
12、ed in due course. Part 8: Specification for locking systems for the load carrying compartment; Part 9: Specification for security of ancillary equipment on CVs; Part 10: Specification for immobilizers. A British Standard does not purport to include all the necessary provisions of a contract. Users o
13、f British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a bac
14、k cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 16:58:44 GMT+00:00 2006, Uncontrolled
15、Copy, (c) BSI BS AU 209-0:1996 BSI 03-19991 Introduction Vehicle security devices provide varying degrees of protection. They are intended to enhance resistance to theft of either the contents of a vehicle or the vehicle itself, by deterring the potential thief from attacking or continuing an attack
16、 on a vehicle. It is accepted that any security system can be overcome given the appropriate skills, tools and time. However, considerable resistance to theft can be provided by the various devices and systems available on the market. The risk of theft can be reduced by taking several precautions. S
17、ome precautions relate to the vicinity in which the vehicle is parked and the condition in which it is left. Others relate to the security devices on the vehicle. The use of good security systems/devices can force a thief to use tools that are difficult to conceal and can make the time needed to ent
18、er the vehicle so long as to make an interruption likely. 1 Scope This British Standard is intended to provide information and guidance on the various types of security devices and systems that are available, the range of protection devices and systems that are available, the range of protection the
19、y offer, and where appropriate the British Standard to which they should conform. Security aspects of how and where the vehicle is left are also considered. 2 Informative references This British Standard refers to other publications that provide information or guidance. Editions of these publication
20、s current at the time of issue of this standard are listed on the inside back cover, but reference should be made to the latest editions. 3 Vehicle perimeter security NOTEThere are several stages, during the process of breaking into a vehicle, at which a thief may be delayed or deterred by appropria
21、te security systems. 3.1 Tampering with the vehicle Indication of fitted security devices will often be sufficient to deter a thief from attempting to break into a vehicle. However, the precise type of system should not be shown, because a thief may know how to defeat particular systems quickly. Som
22、e security systems are fitted with devices (motion sensors, impact sensors, proximity sensors etc.) that will detect interference with the vehicle and sound an alarm prior to the thief intruding into the vehicle. These systems may not be sufficient to deter the thief from attacking the vehicle, but
23、may deter subsequent theft. 3.2 Door security (See BS AU 209-1a, BS AU 209-5b, BS AU 209-6a, BS AU 209-7 and BS AU 209-81) In all thefts from closed vehicles and in nearly all thefts of vehicles, it is necessary for the thief to first gain entry. Entry is usually gained through a door, a window or t
24、he boot. Doors with locking systems conforming to BS AU 209-1a will provide a good basic level of security, without which more sophisticated central and deadlocking systems may not be as effective. Compliance with BS AU 209-1a will prevent the door locks from being easily forced or the internal link
25、ages being simply activated to release the latch mechanisms. BS AU 209-1a also includes requirements to prevent the windows from being forced down easily. Central locking systems that conform to BS AU 209-5b also meet the requirements of Part 1a and ensure that all the doors lock when the driver/pas
26、senger door is locked, so significantly reducing the risk of any door being left inadvertently unlocked. Deadlocking systems that conform to BS AU 209-6a also meet the requirements of Parts 1a and 5b and ensure that locked doors cannot be opened even if the interior handles are accessed from the out
27、side of the vehicle (e.g. by breaking a window). Only a key can be used to unlock this type of door. NOTELocking systems for the drivers and load compartment of goods vehicles which conform to BS AU 209-7 and BS AU 209-8, respectively, should provide a good level of security 3.3 Window security (BS
28、AU 209-4) NOTE 1A thief can gain immediate access to the contents of a vehicle (at least as far as they can reach) by breaking a window. If the vehicle is not deadlocked the thief can then open the door using the interior controls. This will provide much easier access to the contents of the vehicle
29、and will facilitate the theft of the vehicle itself. Security glazing that conforms to BS AU 209-4 should be fitted to increase the window security of a vehicle significantly by increasing the time and effort necessary to break through the glass. NOTE 2Glazing which conforms to BS AU 209-4 is most l
30、ikely to be only available as original equipment on new vehicles. 1) In preparation. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 16:58:44 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 209-0:1996 2 BSI 03-1999 4 Alarm on breach of perimeter security (see B
31、S 6803) NOTEIn the event of the perimeter security of a vehicle being breached, e.g. a window being broken or a door opened, a sounding alarm can be an effective deterrent. However, as the public have become very used to false alarms, a sounding alarm might only be effective if the owner is within e
32、arshot. To be effective, alarm systems should sound only following an attack on a vehicle and should not suffer from false alarms, such as car alarm systems conforming to BS 6803-22) and commercial vehicle alarm systems conforming to BS 6803-3. Installing such alarm systems in compliance with BS 680
33、3-1 will ensure they are effective and reliable in use. 5 Security of in-car entertainment systems (see BS AU 209-2) In-car entertainment systems represent a high proportion of the contents stolen from cars. Compliance with BS AU 209-2 requires the system to be easily removable (by the vehicle owner
34、), or locked in place (by a lock conforming to BS AU 209-1a), or permanently installed, or coded, or of a modular form where the system is split up. In addition the system should be permanently marked with a unique vehicle identification number (VIN) or registration number. 6 Immobilization (BS AU 2
35、09-10) Since 1972 all new cars and light vans are required to be fitted with a device to prevent their unauthorized use. The most common device is a steering column lock which is integral with the ignition/starter control and is activated by the ignition key. It is normal for the design of these dev
36、ices to be common for each model in a vehicle range and because of this most thieves readily know how to overcome them. It is therefore advisable for an additional vehicle immobilizer which conforms to BS AU 209-103) to be fitted, as a thief is less likely to be knowledgeable about its function and
37、installation. Immobilizers fall into three categories as follows: mechanical; electromechanical; and electrical/electronic. Typically, mechanical systems need to be fitted to the vehicle every time it is left, although a fixing point may be permanently fitted. Electromechanical and electrical/electr
38、onic systems are, typically, permanently fitted to the vehicle and need only to be activated each time the vehicle is left. In some cases this activation may be automatic (passive arming). NOTEAn immobilizer that instantaneously immobilizes the engine should not be capable of being activated while t
39、he vehicle is moving, otherwise the safe operation of the vehicle could be severely affected. 7 Aiding the recovery of stolen vehicles NOTEThe true identity of a stolen vehicle has to be disguised in order for the thief to maximize any financial gain from it. If a vehicle gives any indication of its
40、 true identity, it will increase the chance of detection while the thief uses it or tries to pass it on. 7.1 Visible vehicle identification Since April 1980 all new cars are required to be marked with a unique Vehicle Identification Number (VIN). Traditionally the VIN was positioned where it was not
41、 visible from the outside of the vehicle and consequently the police were unable to check it. Increasingly for new vehicles the VIN is being positioned where it is visible from the outside but cannot be tampered with. This is called “Visible VIN” and its use will aid the recovery of stolen vehicles
42、especially if the thief cannot remove or obliterate it. The VIN is the only mark that is unique to the vehicle, and recognized by the police as such. If the VIN is visible it will aid the identification and hence recovery of stolen vehicles which have been abandoned and/or had their identity superfi
43、cially changed (e.g. respray, false plates). Vehicles which do not have a manufacturer-applied “Visible VIN” should have some other unique number etched on the glazing, preferably the registration number or VIN. If this is done in accordance with BS AU 209-3 it will significantly increase the cost o
44、f changing the vehicles identity and will therefore act as a deterrent to a thief. NOTEThe VIN should only be applied in a position visible from the outside of the vehicle with the approval of the vehicle manufacturer, otherwise it may make the acquisition of duplicate keys easier for the thief. 7.2
45、 Hidden identification A vehicle and/or its component parts may be identified by concealed marks or devices. These are not intended to be visible to the naked eye and may be read physically or electronically. The more components and parts of the vehicle that are identifiable using such means, the ha
46、rder it will be for a thief to change the vehicles identity, or sell the component parts. 2) Under revision. 3) In preparation. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 16:58:44 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 209-0:1996 BSI 03-19993 7.3
47、Locating devices These devices can be concealed in a vehicle and enable it to be tracked and located. This kind of device should significantly decrease the recovery time and the number of vehicles that disappear, provided that the body responsible for the search has sufficient resources and a widesp
48、read infrastructure. Further, if the police are able to respond sufficiently fast to a reported vehicle theft, there is a significant chance of the thief being apprehended during the theft. 8 Assessing the security of a vehicle Table 1 summarizes the types and degrees of benefits that might be expec
49、ted to be gained by any particular item of security equipment. It is only intended as a guide. Relative benefits of security only apply to the risk indicated at the head of each column. Therefore, comparisons of benefits should only be made down the columns, and not across the rows. Products that claim conformity with a British Standard should be chosen in favour of ones that do not, as the British Standards have been drawn up to give the user some assurance with regard to the minimum level of security provided and the reliability and safety of
链接地址:https://www.31doc.com/p-3736685.html