BS-AU-214-2-1988 ISO-7646-1986.pdf
《BS-AU-214-2-1988 ISO-7646-1986.pdf》由会员分享,可在线阅读,更多相关《BS-AU-214-2-1988 ISO-7646-1986.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 214-2:1988 ISO 7646:1986 Gearbox flanges Part 2: Specification for dimensions for type A gearbox flanges for commercial vehicles and buses ISO title: Commercial vehicles and buses Gearbox flanges Type A UDC 629.114.4/.53:621.825.24 Licensed Copy: London South
2、 Bank University, London South Bank University, Sat Dec 09 02:05:05 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 214-2:1988 This British Standard, having been prepared under the direction of the Automobile Standards Committee, was published under the authority of the Board of BSI and comes into
3、effect on 29 January 1988 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference AUE/13 Draft for comment 82/75548 DC ISBN 0 580 16364 4 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Automobil
4、e Standards Committee (AUE/-) to Technical Committee AUE/13, upon which the following bodies were represented: British Railways Board Department of Transport (Highways) Freight Transport Association Institute of Road Transport Engineers (Incorporated) London Regional Transport Ministry of Defence Na
5、tional Bus Company Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:05:05 GMT+00:00 2006, Uncontrolled Copy, (c)
6、BSI BS AU 214-2:1988 BSI 12-1999i Contents Page Committees responsibleInside front cover National forewordii 1Scope and field of application1 2References1 3Dimensions and tolerances1 4Designation1 Figure 12 Figure 22 Figure 33 Figure 43 Figure 54 Table Dimensions and tolerances4 Publications referre
7、d toInside back cover Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:05:05 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 214-2:1988 ii BSI 12-1999 National foreword This British Standard has been prepared under the direction of the Automobile Standards Co
8、mmittee and is identical with ISO 7646:1986 “Commercial vehicles and buses Gearbox flanges Type A”, published by the International Organization for Standardization (ISO). Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British St
9、andard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. The comma has been used as a decimal marker. In British Standards it is current practice to use a full point on the baseline as t
10、he decimal marker. Wherever the words “International Standard” appear, referring to this standard, they should be read as “British Standard”. The Technical Committee has reviewed the provisions of ISO 1101:1983 to which reference is made in the text, and has decided that they are acceptable for use
11、in conjunction with this standard. A related British Standard to ISO 1101 is BS 308 “Engineering drawing practice” Part 3:1972 “Geometrical tolerancing”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their co
12、rrect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International StandardCorresponding British Standard ISO/R 286:1962BS 4500 ISO limits and fits Part 1:1969 General, tolerances and deviations (Technically equivalent) ISO
13、 7647:1986BS AU 214 Gearbox flanges Part 3:1987 Specification for dimensions for type S gearbox flanges for commercial vehicles and buses (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. Th
14、is standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:05:05 GMT+00:00 2006, Uncontrolled Copy, (c) B
15、SI BS AU 214-2:1988 BSI 12-19991 1 Scope and field of application This International Standard specifies the nominal dimensions and tolerances which affect the interchangeability between gearbox flanges and mating parts used on commercial vehicles and buses. The flanges covered by this International
16、Standard are designated type A. They are not interchangeable with type S flanges dealt with in ISO 7647. Dimensions not specified are left to the discretion of the component manufacturer. 2 References ISO 286, ISO system of limits and fits1). ISO 1101, Technical drawings Geometrical tolerancing Tole
17、rancing of form, orientation, location and run-out Generalities, definitions, symbols, indications on drawings. ISO 7647, Road vehicles Gearbox flanges for commercial vehicles and buses Type S. 3 Dimensions and tolerances Nominal dimensions, tolerances and bolt hole fixing positions which affect the
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-214-2-1988 ISO-7646-1986 BS AU 214 1988 ISO 7646 1986
链接地址:https://www.31doc.com/p-3736696.html