BS-AU-262-2-1995 ISO-6550-2-1994.pdf
《BS-AU-262-2-1995 ISO-6550-2-1994.pdf》由会员分享,可在线阅读,更多相关《BS-AU-262-2-1995 ISO-6550-2-1994.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 262-2:1995 BS ISO 6550-2:1994 Incorporating Amendment No. 1 Road vehicles Sheath-type glow-plugs with conical seating and their cylinder head housing Part 2: M12 ? ? 1.25 glow-plugs ICS 43.060.50 ? Licensed Copy: London South Bank University, London South Ban
2、k University, Sat Dec 09 02:13:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 262-2:1995 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 December 1995 BSI 20 Dec
3、ember 2002 The following BSI references relate to the work on this standard: Committee reference MCE/9 Draft for comment 94/704885 DC ISBN 0 580 24942 5 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee MCE/9, Ignition equi
4、pment for spark ignition engines, upon which the following bodies were represented: Society of Motor Manufacturers and Traders Ltd. Coopted members Amendments issued since publication Amd. No.DateComments 1410420 December 2002Change to secondary identifier Licensed Copy: London South Bank University
5、, London South Bank University, Sat Dec 09 02:13:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 262-2:1995 BSI 20 December 2002 i Contents Page Committees responsibleInside front cover National forewordii 1Scope1 2Normative references1 3Dimensions and tolerances1 4Installation tightening torque
6、1 Figure 1 M12 ? 1,25 sheath-type glow-plug with conical seating2 Figure 2 Cylinder head housing for glow-plug3 Table 1 Installation tightening torque1 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:13:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 262-
7、2:1995 ii BSI 20 December 2002 National foreword This British Standard has been prepared by Technical Committee MCE/9. It is identical with ISO 6550-2:1994 Road vehicles Sheath-type glow-plugs with conical seating and their cylinder head housing Part 2: M12 ? 1,25 glow-plugs, published by the Intern
8、ational Organization for Standardization (ISO). A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obliga
9、tions. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 3 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Licensed Copy: London South Bank University, London South Bank Univers
10、ity, Sat Dec 09 02:13:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 262-2:1995 BSI 20 December 2002 1 1 Scope This part of ISO 6550 specifies the main characteristics of M12?1,25 sheath-type glow-plugs with conical seating and their cylinder head housing, for use with diesel (compression-ignit
11、ion) engines. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 6550. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based
12、 on this part of ISO 6550 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 2705:1991, Road vehicles M12 ? 1,25 spark-plugs with flat seating a
13、nd their cylinder head housing. ISO 8092-1:, Road vehicles Connections for on-board electric harnesses Part 1: Single-pole connector tabs Dimensions and specific requirements.1) 3 Dimensions and tolerances 3.1 Glow-plugs Sheath-type glow-plug dimensions and tolerances are given in Figure 1. 3.2 Cyli
14、nder head housing The dimensions and tolerances of the cylinder head housing for sheath-type glow-plugs are given in Figure 2. 3.3 Dimension limits of thread The threads of M12?1,25 glow-plugs and the corresponding tapped holes in the cylinder head shall conform to the threads specified for M12?1,25
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-262-2-1995 ISO-6550-2-1994 BS AU 262 1995 ISO 6550 1994
链接地址:https://www.31doc.com/p-3736704.html