BS-AU-50-3.5-1983 ISO-7442-1982.pdf
《BS-AU-50-3.5-1983 ISO-7442-1982.pdf》由会员分享,可在线阅读,更多相关《BS-AU-50-3.5-1983 ISO-7442-1982.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 50-3.5:1983 ISO 7442:1982 Specification for Tyres and wheels Part 3: Valves Section 5: Dimensions for ISO core chamber No. 1 for tyre inflation valves ISO title: Tyre valves ISO core chamber No. 1 UDC 629.113.012.551-396.2 Licensed Copy: London South Bank Uni
2、versity, London South Bank University, Sat Dec 09 01:52:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-3.5:1983 This British Standard, having been prepared under the direction of the Automobile Standards Committee, was published under the authority of the Board of BSI and comes into effect o
3、n 28 February 1983 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/4 Draft for comment 81/75414 DC ISBN 0 580 132048 Cooperating organizations The Automobile Standards Committee, under whose direction this British Standard was prepared, consists
4、of representatives from the following: Amalgamated Union of Engineering Workers Auto-cycle Union Automobile Association British Rubber Manufacturers Association* British Steel Industry Confederation of British Road Passenger Transport Department of Industry (Mechanical Engineering) Department of the
5、 Environment (Transport and Road Research Laboratory)* Department of Transport (Highways)* Freight Transport Association Limited* Institute of Purchasing and Supply Institution of Mechanical Engineers Institution of Production Engineers London Transport Executive* Ministry of Defence* Motor Cycle As
6、sociation of Great Britain* National Caravan Council Limited National Freight Corporation (NFC) Ltd. Road Haulage Association Ltd. Royal Automobile Club Society of Motor Manufacturers and Traders Limited The organizations marked with an asterisk in the above list, together with the following, were d
7、irectly represented on the Technical Committee entrusted with the preparation of this British Standard: Agricultural Engineers Association British Industrial Fasteners Federation British Industrial Truck Association British Pressure Gauge Manufacturers Association Motor Industry Research Association
8、 Retread Manufacturers Association Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:52:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-3.5:1983 BSI 02-2000i Contents Page Cooperating orga
9、nizationsInside front cover National forewordii 1Scope and field of application1 2References1 3Dimensions1 Annex Counterbore dimensions3 Figure 1 Core chamber1 Figure 2 Core pin head position Tolerances2 Figure 3 Counterbore dimensions3 Table Core chamber dimensions2 Publications referred toInside b
10、ack cover Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:52:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-3.5:1983 ii BSI 02-2000 National foreword This Section of this Part of BS AU 50, prepared under the direction of the Automobile Standards Commi
11、ttee, is identical with ISO 7442:1982 “Tyre valves ISO core chamber No. 1” published by the International Organization for Standardization (ISO). Sections 1, 2, 3, 4 and 6 of this Part deal with valve dimensions. Other Parts of the standard are: Part 1: Tyres; Part 2: Wheels and rims. Terminology an
12、d conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. Where the word
13、s “International Standard” appear, referring to this standard, they should be read as “British Standard”. The comma has been used throughout as a decimal marker. In British Standards it is current practice to use a full point on the baseline as the decimal marker. A British Standard does not purport
14、 to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International StandardCorresponding British Standard ISO 15
15、02:1978BS 919 Screw gauge limits and tolerances Part 3:1968 Gauges for ISO metric screw threads (Technically equivalent) ISO 4570-1:1977BS AU 50 Tyres and wheels Part 3:Section 2:1977 Tyre valve threads 5V1, 5V2, 6V1 and 8V1 (Identical) Summary of pages This document comprises a front cover, an insi
16、de front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, Lon
17、don South Bank University, Sat Dec 09 01:52:22 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-3.5:1983 BSI 02-20001 1 Scope and field of application This International Standard specifies the interchangeability dimensions of an ISO core chamber No. 1, and applies principally to core chambers of
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-50-3.5-1983 ISO-7442-1982 BS AU 50 3.5 1983 ISO 7442 1982
链接地址:https://www.31doc.com/p-3736757.html