BS-AU-91-1965.pdf
《BS-AU-91-1965.pdf》由会员分享,可在线阅读,更多相关《BS-AU-91-1965.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 91:1965 Specification for Dimensions of electrical cable connectors for starter battery taper terminal posts (Cars and light commercial vehicles using positive earth system) UDC 629.113.066:621.315.683:621.356.035.5 Licensed Copy: London South Bank University
2、, London South Bank University, Sat Dec 09 01:52:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 91:1965 This British Standard, having been approved by the Automobile Industry Standards Committee and endorsed by the Chairman of the Engineering Divisional Council, was published under the authorit
3、y of the General Council of the Institution on 30 September 1965 BSI 02-2000 The following BSI reference relates to the work on this standard: Committee reference AUE/- ISBN 0 580 34554 8 Amendments issued since publication Amd. No.DateComments Licensed Copy: London South Bank University, London Sou
4、th Bank University, Sat Dec 09 01:52:26 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 91:1965 BSI 02-2000i Contents Page Figure 1 Cable connectors1 Figure 2 Lighting circuit cable connector2 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:52:26 GMT+00:00 2
5、006, Uncontrolled Copy, (c) BSI BS AU 91:1965 ii BSI 02-2000 This British Standard, which is published under the authority of the Automobile Industry Standards Committee of the BSI is based upon data-sheet SMMT 181:1961 of the Society of Motor Manufacturers and Traders Ltd. It specifies the dimensio
6、ns for positive and negative electrical cable connectors for attachment to the starter battery terminal posts specified in BS.1) on cars and light commercial vehicles using the positive earth system. These cable connectors are alternative to those specified in BS AU 312). The dimensions of the conne
7、ctors shall be as shown in Figure 1. The connectors shall be attached to the battery terminal posts by means of No. 10 self-tapping screws * in long. The dimensions of the lighting circuit cable connector for attachment to the negative battery connector shall be as shown in Figure 2. NOTEIf it is re
8、quired to convert the figures in this standard from British units into metric units it is recommended that the conversion factors and the tables contained in BS 350, “Conversion factors and tables”, be used. Attention is also drawn to BS 2856, “Precise conversion of inch and metric sizes on engineer
9、ing drawings”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This docu
10、ment comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. 1) BS., “Starter batteries for i
11、nternal combustion engines”. (In course of preparation). 2) BS AU 31, “Dimensions of electrical cable connectors for starter battery taper terminal posts (cars and light commercial vehicles)”. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:52:26 GMT+00:00 20
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS AU 91 1965
链接地址:https://www.31doc.com/p-3736903.html