《BS-CECC-23600-801-1998.pdf》由会员分享,可在线阅读,更多相关《BS-CECC-23600-801-1998.pdf(24页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS CECC 23600-801: 1998 Harmonized system of quality assessment for electronic components Capability detail specification: Flex-rigid multilayer printed boards with through connections ICS 31.180 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 0
2、1:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS CECC 23600-801:1998 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 June 1998 BSI 05-1999 ISBN 0 580 29890
3、6 National foreword This British Standard is the English language version of CECC 23600-801:1998 published by the European Eelectronic Components Committee (CECC) of the European Committee for Electrotechnical Standardization (CENELEC). This standard should be read in conjunction with the most recen
4、t editions of BS EN 123000 and BS EN 123600. The UK participation in its preparation was entrusted to Technical Committee EPL/501, Electronic assembly technology, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any en
5、quiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The B
6、ritish Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A Bri
7、tish Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a fro
8、nt cover, an inside front cover, pages i and ii, the CECC title page, pages 2 to 19 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publica
9、tion Amd. No.DateComments Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS CECC 23600-801:1998 BSI 05-1999i Contents Page National forewordInside front cover Foreword2 Text of CECC 23 600-8013 Licensed Copy:
10、London South Bank University, London South Bank University, Sat Dec 09 01:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI DETAIL SPECIFICATION SPCIFICAT
11、ION PARTICULIRE BAUARTSPEZIFIKATION CECC 23 600-801 February 1998 English version Capability Detail Specification: Flex-rigid multilayer printed boards with through connections Spcification particulire dAgrment: Cartes imprimes multicouches flexorigides avec connexions transversales Bauartspezifikat
12、ion zur Anerkennung der Befhigung: Starr-flexible Mehrlagen-Leiterplatten mit Durchverbindungen This Capability Detail Specification was approved on 1997-08-06. Up-to-date lists and bibliographical references of other detail specifications relating to EN 123000:1991 and EN 123600:1996 may be obtaine
13、d on application to the Central Secretariat or to any CENELEC member. This CECC Detail Specification exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the
14、 Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerla
15、nd and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1998 CENELEC All rights of exploitation in any form and by
16、any means reserved worldwide for CENELEC members. Ref. No. CECC 23 600-801:1998 E Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CECC 23 600-801:1998 BSI 05-1999 2 Foreword This Capability Detail Specification
17、 has been prepared by CENELEC/TC CECC/SC 52, Printed Boards (formerly designated CECC Working Group 23). It was approved as CECC 23 600-801 on 1997-08-06. It should be read in conjunction with EN 123000:1991 and EN 123600:1996 and with the current regulations for the CECC System. Contents Page Forew
18、ord2 1General3 1.1Scope3 1.2Object3 2Capability qualifying component3 2.1Materials3 2.2Surface finishes4 2.2.1Metallic finishes4 2.2.1.1Accelerated ageing4 2.2.2Organic finishes4 2.3Variant designation5 3Capability approval5 3.1Range of capability approval5 3.2QPL information5 4Capability test progr
19、amme5 4.1Capability demonstration5 4.1.1Other metallic surface finishes5 4.1.2Organic surface finishes6 5Additional capability6 6Traceability6 Annex A Edge connector imperfections18 Annex B Circumferential defects in plated-through holes19 Table I Capability approval test schedule7 Table IIa Additio
20、nal metallic conductor finishes12 Table lIb Additional contact finishes15 Table III Permanent organic finishes16 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CECC 23 600-801:1998 BSI 05-19993 1 General 1.1 S
21、cope This Capability Detail Specification (CapDS) is based upon EN 123600. It relates to flex-rigid multilayer printed boards with through connections, made with materials and surface finishes as specified in clause 2. 1.2 Object To specify the Capability Qualifying Component (CQC), its characterist
22、ics to be tested, the test methods and conditions to be applied and the requirements to be fulfilled for testing basic and extended capability. 2 Capability Qualifying Component (CQC) Test boards to be used as CQCs for basic capability shall: be made from a combination of the materials specified in
23、2.1 of this CapDS. The construction shall be as given in 8.3 of EN 123600. bear the composite test pattern (CTP) specified in 8.3 of EN 123600 (or equivalent CTP), for basic and other metallic finishes. CTPs as specified in 8.2 of EN 123200 (or equivalent CTP) shall be used to demonstrate organic su
24、rface finishes and external bonded heat sinks. have one of the surface finishes specified by groups 11, 12, 13, 14, 15, 16, or 18 in 2.2 of this CapDS. Requirements for test boards to be used as modified CQCs for the demonstration of additional capability are detailed in clause 5 of this CapDS. 2.1
25、Materials Material group designation SpecificationBase MaterialBase material (thickness range) Cu thickness TypeGrade(4m) AEN 60249-2-11Epoxide woven glass General purpose0,05 0,8 mm18, 35 70, 105 EN 60249-2-12Epoxide woven glass Defined flammability $ 0,05 mm EN 60249-3-1GPrepregGeneral purpose EN
26、60249-3-1GFPrepregDefined flammability $ 0,05 mmn.a. BEN 60249-2-8Polyester (PETP) film General Purpose 12,5 125 4m EN 60249-2-13Polyimide filmGeneral purpose12,5 125 4m18, 35, 70 EN 60249-2-15Polyimide filmDefined flammability 12,5 125 4m Licensed Copy: London South Bank University, London South Ba
27、nk University, Sat Dec 09 01:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CECC 23 600-801:1998 4 BSI 05-1999 2.2 Surface finishes 2.2.1 Metallic finishes The demonstration of metallic group finishes 21, 22, 23 or 24 shall be combined with a finish from groups 11, 12, 13, 14, 15, 16 or 18. Each c
28、laimed combination of metallic finishes shall be tested separately. Selective and non-selective finishes of the same material, where claimed, shall be demonstrated separately. 2.2.1.1 Accelerated ageing The ability of finish groups 11, 12, 13, 14, 15, 16 or 18 to solder after extended or adverse sto
29、rage conditions is demonstrated using accelerated ageing. This test shall be carried out on those finishes where accelerated ageing is claimed. Each finish that has complied with the requirements of the ageing test is highlighted by the inclusion of an asterisk (*) adjacent to that finish in the man
30、ufacturers abstract of capability as published in the QPL. 2.2.2 Organic finishes (where claimed) The demonstration of organic finish groups a, b, c,d, e, f or g shall be over a finish from groups 11, 12, 13, 14, 15, 16, or 18. All claimed types of solder resist shall be tested separately. Finish gr
31、oup Designation Surface finishAbbreviation for QPL Remarks 11Bare copperCu 12Copper with solderable organic protective coatingCu(opc) 13Copper with oxideCu(CuO) 14Tin, Tin-LeadSn, SnPb 15Tin-Lead (fused)SnPb(f) 16Tin-Lead (dipped and levelled)SnPb(dl) 17not assigned 18Immersion Gold over Electroless
32、 NickelAuNi(smt) 19not assigned 20not assigned 21Specimen K 5 4m, gold plated on copper, remainder using finish group 1117 (see below) 5AuCu 22Specimen K 0,7 4m, gold plated on nickel, remainder using finish group 1117 (see below) 0,7AuNi 23Specimen K 2,5 4m, gold plated on copper, remainder using f
33、inish group 1117 (see below) 2,5AuCu 24Specimen K 2,5 4m, gold plated on nickel, remainder using finish group 1117 (see below) 2,5AuNi Finish group designation Organic finishAbbreviation for QPL aAdhesive Coated film coverlayerAFC bDry film solder maskDSM cWet resist solder mask/coverlayerWSM dLiqui
34、d photopolymer solder maskLSM eLiquid Photopolymer coverlayerLPC fMarking inksMI gConductive InkCI Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CECC 23 600-801:1998 BSI 05-19995 2.3 Variant designation The c
35、ombination of any material group designated in 2.1 and any of the surface finishes designated in 2.2 constitutes a variant. The variant is designated by the combination of both material and finish group designations. e.g. A12(b) or A12/21(c). 3 Capability approval 3.1 Range of capability approval Ca
36、pability approval granted on the testing of one variant is valid within the limits specified in 3.7 of EN 123000 for metal clad base material within one group designation, all base material thicknesses and all foil thicknesses of the material in accordance with 2.1 of this CapDS; and all metallic su
37、rface finishes within one surface finish group as given in 2.2.1 of this CapDS, that is 3.2 QPL information Information for the QPL (published as CECC 00 200) shall be given in accordance with 3.4 of EN 123000, and shall contain the following details relative to the CapDS: 4 Capability test programm
38、e NOTEIn all cases the number of failures permitted is zero. 4.1 Capability demonstration Capability shall be demonstrated using 9 CTPs, of one variant from each material group claimed. Testing shall be in accordance with Table I. 4.1.1 Other metallic surface finishes If claimed, other metallic surf
39、ace finishes, as designated in 2.2.1 shall be demonstrated by the manufacture and testing of 3 CTPs plus sufficient extra A and H specimens to meet the requirements of Table II. The maximum active board size for the finish shall be demonstrated. See also clause 5. finish group 11covers finish group
40、11 only finish group 12covers finish group 11 and 12 finish group 13covers finish group 11 and 13 finish group 14covers finish group 11 and 14 finish group 15covers finish group 11 and 15 finish group 16covers finish group 11 and 16 finish group 18covers finish group 18 only finish group 21covers fi
41、nish group 21 only finish group 22covers finish group 22 and 24 finish group 23covers finish group 21 and 23 finish group 24covers finish group 24 only wreference to the CECC Generic SpecificationEN 123000 wreference to the CECC Sectional SpecificationEN 123600 wreference to the CECC CapDSCECC 23 60
42、0-801 wbase material for which approval is grantedas given in 2.1 of this CapDS wthe surface finishes for which approval is grantedas given in 2.2 of this CapDS wany additional capability3.5.3 of EN 123000 refers Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 0
43、1:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CECC 23 600-801:1998 6 BSI 05-1999 4.1.2 Organic surface finishes Each claimed organic surface finish, as designated in 2.2.2, shall be demonstrated by the manufacture and testing of 3CTPs using the pattern specified in Annex A (marking inks) or Ann
44、ex B (solder masks) of CECC 23 200-801. Testing shall be in accordance with Table III of this CapDS. 5 Additional capability 6 Traceability Traceability of all specimens to the original product shall be maintained. The method used to identify individual test specimens shall not prejudice the test re
45、sult. Maximum active board sizesee 8.3 of EN 123000 Minimum conductor width and spacing Specimen F of the CTP to be modified to provide additionally 5 conductors and 4 spacings, each of the claimed minimum. Initial foil thickness of less than 35 4m may be used for this demonstration, but the thickne
46、ss used shall be declared. Metallic conductor finishesManufacturers are permitted to demonstrate conductor finishes other than those detailed in 2.2.1. The finish shall be demonstrated in accordance with Table IIa and detailed in the manufacturers Capability Manual. Licensed Copy: London South Bank
47、University, London South Bank University, Sat Dec 09 01:23:13 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CECC 23 600-801:1998 BSI 05-19997 Table I Capability approval test schedule Characteristics Test No. IEC 60326-2 Specimen of Composite Test Pattern RequirementsRemarks General examination Visual
48、examination Conformity and identification 1All CQCsPattern, marking, identification, material and finishes shall comply with this CapDS. There shall be no apparent defects. Any identification for traceability purposes shall be verified. Appearance and workmanship 1aAll CQCsThe boards shall appear to
49、 have been processed in a careful and workmanlike manner, in accordance with good current practice. The base materials, conductors, surface finishes shall be of uniform appearance and free from cracks, burns, pits, nodules and blisters. Metallic surface finishes shall be free from scratches which penetrate to an underlying surface. Plated-through holesAll CQCsPlated-through holes shall be clean and free from inclusions of any sort that could affect component insertion and solderability, Total area of the voids shall not exceed 10 % of
链接地址:https://www.31doc.com/p-3736918.html