《BS-EN-10220-2002.pdf》由会员分享,可在线阅读,更多相关《BS-EN-10220-2002.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10220:2002 Incorporating corrigendum no. 1 Seamless and welded steel tubes Dimensions and masses per unit length The European Standard EN 10220:2002 has the status of a British Standard ICS 23.040.10; 77.140.70 ? BS EN 10220:2002 This British Standard, having been prepared und
2、er the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 13 December 2002 BSI 2007 ISBN 0 580 40982 1 National foreword This British Standard is the official English language version of EN 10220:2002
3、. It supersedes BS 3600:1997 and DD ENV 10220:1994 which are withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/8, Steel pipes, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary.
4、 This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible
5、international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Amendments issued since publication Amd. No. DateComments 16892 Corrigendum No. 1
6、28 February 2007 Revision of supersession details. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10220 December 2002 ICS 23.040.10; 77.140.70 English version Seamless and welded steel tubes - Dimensions and masses per unit length Tubes lisses en acier, souds et sans soudure - Tableaux gnraux
7、des dimensions et des masses liniques Nahtlose und geschweite Stahlrohre - Allgemeine Tabellen fr Mae und lngenbezogene Masse This European Standard was approved by CEN on 16 October 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for gi
8、ving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versi
9、ons (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cze
10、ch Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: ru
11、e de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10220:2002 E EN 10220:2002 (E) 2 Contents page Foreword3 1Scope 4 2Normative references 4 3Terms and definitions4 4Classification of outside diam
12、eters .4 5Method of calculating masses per unit length5 6Dimensions and masses per unit length.5 Bibliography9 EN 10220:2002 (E) 3 Foreword This document (EN 10220:2002) has been prepared by Technical Committee ECISS/TC 29, “Steel tubes and fittings for steel tubes“, the Secretariat of which is held
13、 by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2003, and conflicting national standards shall be withdrawn at the latest by June 2003. When transforming the European Prestandard ENV
14、 10220 into this European Standard EN 10220, ECISS/TC 29 regarded it as necessary to avoid any conflict with and to deviate as little as possible from ISO 4200:1991 because of the international trade in steel tubes and tubular products. Table 1 of ENV 10220, which is identical with Table 2 of ISO 42
15、00:1991, was therefore left unchanged for EN 10220. Table 2 of EN 10220 contains dimensions for heavy wall tubes, that are not covered by ISO 4200:1991. All parts of the European Standard series EN 10305 on steel tubes for precision applications contain tables with preferred dimensions, that are spe
16、cific for the various parts of the standards series and the products and fields of application specified therein. Therefore, Table 3 from ENV 10220 with preferred dimensions for steel tubes for precision applications has become unnecessary, and has not been included in this standard. This document s
17、upersedes ENV 10220:1993. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg
18、, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. EN 10220:2002 (E) 4 1 Scope This European Standard specifies, for seamless and welded circular steel tubes for general purposes (e. g. mechanical, pressure and structural applications), the following: preferre
19、d dimensions for outside diameter and wall thickness in millimetres and masses per unit length in kilogrammes per metre of plain end tube. Technical Committees of ECISS and CEN should select these preferred dimensions for their product or functional standards, where appropriate. The outside diameter
20、s are classified into three series reflecting the availability of accessories for piping systems (see Clause 4). This classification of outside diameters into different series and of preferred wall thicknesses indicates the range of steel tubes usually produced. NOTE Information on dimensions for st
21、eel tubes for special applications can be found in other European Standards, e.g. prEN 10255, EN 10305 series, EN ISO 11960 and EN ISO 11961, information on dimensions for stainless steel tubes in EN ISO 1127. 2 Normative references This European Standard incorporates by dated or undated reference,
22、provisions from other publications. These normative references are cited at the appropriate places in the text and publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it
23、by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). prEN 10266, Steel tubes, fittings and structural hollow sections Symbols and definition of terms for use in product standards. 3 Terms and definitions For the purpose of
24、 this European Standard the terms and definitions in prEN 10266 apply. 4 Classification of outside diameters The outside diameters given in Tables 1 and 2 are classified into three series which may be described in the following way: series 1: outside diameters for which all the accessories needed fo
25、r the construction of piping systems are standardized; series 2: outside diameters for which not all accessories are standardized; series 3: outside diameters for which very few standardized accessories exist. NOTE 1 It is recommended to select, for tubes intended to be used as components of piping
26、systems, outside diameters from series 1 in Table 1. Tubes with outside diameters in accordance with series 2 and 3 may not, or not easily, be available. NOTE 2 Accessories for heavy wall tubes with dimensions in accordance with Table 2 may not be available regardless of the series in Table 1 to whi
27、ch the relevant outside diameter is allocated. EN 10220:2002 (E) 5 5 Method of calculating masses per unit length The masses per unit length given in Tables 1 and 2 have been calculated from outside diameter D and wall thickness T to at least five significant figures, using the formula given below.
28、They have been rounded to three significant figures for values of less than 100 and to the nearest whole number for larger values. M = (D - T) T x 0,02466151) kg/m where Mis the mass per unit length in kg/m, Dis the specified outside diameter in mm and Tis the specified wall thickness in mm. The cal
29、culated values may also be applied to tubes with different density values, but have then to be multiplied by a factor of 1,015 for austenitic stainless steel2) 0,985 for ferritic and martensitic stainless steel3) . NOTE EN 10088-1 provides distinguished density values for various groups of stainless
30、 steel grades which may be used for calculating purposes. 6 Dimensions and masses per unit length Table 1 gives dimensions consisting of outside diameters D, from 3 series as described in Clause 4, and related wall thicknesses T 65 mm and the calculated masses per unit length of plain end tube. Tabl
31、e 2 gives dimensions consisting of outside diameters D and related wall thicknesses T from 70 mm to 100 mm and the calculated masses per unit length of plain end tube. 1)This factor is based on a density of 7,85 kg/dm. 2)This factor is based on a density of 7,97 kg/dm. 3)This factor is based on a de
32、nsity of 7,73 kg/dm. EN 10220:2002 (E) 6 Table 1 Dimensions (wall thicknesses T 65 mm) and masses per unit length Wall thickness T, mmOutside diameter D mm series 0,50,60,811,21,41,61,822,32,62,93,23,644,555,45,66,3 123Mass per unit length, kg/m 10,20,1200,1420,1850,2270,2660,3040,3390,3730,4040,448
33、0,487 120,1420,1690,2210,2710,3200,3660,4100,4530,4930,5500,6030,6510,694 12,70,1500,1790,2350,2890,3400,3900,4380,4840,5280,5900,6480,7010,750 13,50,1600,1910,2510,3080,3640,4180,4700,5190,5670,6360,6990,7580,8130,879 140,1660,1980,2600,3210,3790,4350,4890,5420,5920,6640,7310,7940,8520,923 160,1910
34、,2280,3000,3700,4380,5040,5680,6300,6910,7770,8590,9371,011,101,18 17,20,2060,2460,3240,4000,4740,5460,6160,6840,7500,8450,9361,021,101,211,31,41 180,2160,2570,3390,4190,4970,5730,6470,7190,7890,8910,9871,081,171,281,381,50 190,2280,2720,3590,4440,5270,6080,6870,7640,8380,9471,051,151,251,371,481,61
35、1,73 200,2400,2870,3790,4690,5560,6420,7260,8080,8881,001,121,221,331,461,581,721,85 21,30,2560,3060,4040,5010,5950,6870,7770,8660,9521,081,201,321,431,571,711,862,012,12 220,2650,3170,4180,5180,6160,7110,8050,8970,9961,121,241,371,481,631,781,942,102,21 250,3020,3610,4770,5920,7040,8150,9231,031,13
36、1,291,441,581,721,902,072,282,472,612,682,91 25,40,3070,3670,4850,6020,7160,8290,9391,051,151,311,461,611,751,942,112,322,522,662,732,97 26,90,3260,3890,5150,6390,7610,8800,9981,111,231,401,561,721,872,072,262,492,702,862,943,20 300,3640,4350,5760,7150,8520,9871,121,251,381,571,761,942,112,342,562,8
37、33,083,283,273,68 31,80,3860,4620,6120,7600,9061,051,191,331,471,671,872,072,262,502,743,033,303,523,623,96 320,3880,4650,6160,7650,9111,061,201,341,481,681,892,082,272,522,763,053,333,543,653,99 33,70,4090,4900,6490,8060,9621,121,271,421,561,781,992,202,412,672,933,243,543,773,884,26 350,4250,5090,
38、6750,8381,001,161,321,471,631,852,082,302,512,793,063,383,703,944,064,46 380,4620,5530,7340,9121,091,261,441,611,782,022,272,512,753,053,353,724,074,344,474,93 400,4870,5830,7730,9621,151,331,521,701,872,142,402,652,903,233,553,944,324,614,755,24 42,40,5170,6190,8211,021,221,421,611,801,992,272,552,
39、823,093,443,794,214,614,935,085,61 44,50,5430,6500,8621,071,281,491,691,902,102,392,692,983,263,634,004,444,875,215,375,94 48,30,7060,9371,171,391,621,842,062,282,612,933,253,563,974,374,865,345,715,906,53 510,7460,9901,231,471,711,952,182,422,763,103,443,774,214,645,165,676,076,276,94 540,7901,051,
40、311,561,822,072,322,562,933,303,654,014,474,935,496,045,476,687,41 570,8351,111,381,651,922,192,452,713,103,493,874,254,745,235,836,416,877,107,88 60,30,8831,171,461,752,032,322,602,883,293,704,114,515,035,556,196,827,317,558,39 63,50,9311,241,541,842,142,442,743,033,473,904,334,765,325,876,557,217,
41、748,008,89 701,371,702,042,372,703,033,353,844,324,805,275,906,517,278,018,608,899,90 731,421,782,122,472,823,163,504,014,515,015,516,166,817,608,389,009,3110,4 76,11,491,852,222,582,943,303,654,194,715,245,756,447,117,958,779,429,7410,8 82,51,612,012,412,803,193,583,974,555,125,696,267,007,748,669,
42、5610,310,611,8 88,91,742,172,603,023,443,874,294,915,536,156,767,578,389,3710,311,111,512,8 101,62,973,463,954,434,915,636,357,067,778,709,6310,811,912,813,314,8 1083,163,684,204,715,236,006,767,528,279,2710,311,512,713,714,115,8 114,33,353,904,454,995,546,357,167,978,779,8310,912,213,514,515,016,8
43、1274,955,566,177,077,988,889,7711,012,113,615,016,216,818,8 1335,185,826,467,418,369,3010,211,512,714,315,817,017,619,7 139,75,456,126,797,798,799,7810,812,113,415,016,617,918,520,7 141,35,516,196,877,888,899,9010,912,213,515,216,818,118,721,0 152,45,956,697,428,519,6110,711,813,214,616,418,219,620,
44、322,7 1596,216,987,748,8910,011,212,313,815,317,119,020,521,223,7 168,36,587,398,209,4210,611,813,014,616,218,220,121,722,525,2 177,87,818,679,9511,212,513,815,517,119,221,323,023,826,6 193,78,529,4610,912,313,615,016,918,721,023,325,126,029,1 219,19,6510,712,313,915,517,019,121,223,826,428,529,533,
45、1 244,512,013,715,517,319,021,423,726,629,531,833,037,0 27313,415,417,319,321,323,926,529,833,035,636,941,4 323,920,623,025,328,431,635,439,342,444,049,3 355,622,625,227,831,334,739,043,246,648,354,3 406,425,928,931,835,839,744,649,553,455,462,2 45735,840,344,750,256,760,162,370,0 50839,844,849,755,
46、962,066,969,477,9 55943,949,354,761,568,373,776,485,9 61047,953,859,867,274,680,583,593,8 66064,772,780,887,290,4102 71169,778,487,194,097,4109 76274,884,193,3101104117 81379,889,799,6108112125 86484,895,4106114119133 91489,8101112121125141 101699,8112125135140157 1067131141147165 1118137148154173 1
47、168143155161180 1219150162168188 1321182204 1422196220 1524236 1626252 1727 1829 1930 2032 2134 2235 2337 2438 2540 EN 10220:2002 (E) 7 Table 1 (continued) Wall thickness T, mmOutside diameter D mm series 7,188,8101112,514,21617,52022,22528303236404550556065 123Mass per unit length, kg/m 10,2 12 12,
48、7 13,5 14 16 17,2 18 19 20 21,3 22 25 25,4 26,93,473,73 304,014,34 31,84,324,70 324,364,74 33,74,665,075,40 354,895,335,69 385,415,926,346,91 405,766,316,777,40 42,46,186,797,297,99 44,56,557,207,758,519,099,86 48,37,217,958,579,4510,111,0 517,698,489,1610,110,911,9 548,219,089,8110,911,712,813,9 57
49、8,749,6710,511,612,513,715,0 60,39,3210,311,212,413,414,716,117,5 63,59,8810,911,913,214,215,717,318,7 7011,012,213,314,816,017,719,521,322,7 7311,512,813,915,516,818,720,622,524,0 76,112,113,414,616,317,719,621,723,725,327,7 82,513,214,716,017,919,421,623,926,228,130,833,0 88,914,316,017,419,521,123,626,228,830,834,036,539,4 101,616,518,520,122,624,627,530,633,836,340,243,547,250,8 10817,719,721,524,226,329,432,836,339,143,447,051,255,257,7 114,318,821,0
链接地址:https://www.31doc.com/p-3737014.html