BS-EN-10258-1997.pdf
《BS-EN-10258-1997.pdf》由会员分享,可在线阅读,更多相关《BS-EN-10258-1997.pdf(12页珍藏版)》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 10258 : 1997 Incorp
2、orating Amendment No. 1 The European Standard EN 10258 : 1997 has the status of a British Standard ICS 77.140.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Cold-rolled stainless steel narrow strip and cut lengths Tolerances on dimensions and shape This British Standard, h
3、aving been prepared under the direction of the Sector Board for Engineering, was published under the authority of the Standards Board and comes into effect on 15 September 1997 BSI 1998 ISBN 0 580 28314 3 BS EN 10258 : 1997Issue 2, January 1998 Amendments issued since publication Amd. No.DateText af
4、fected 9862January 1998 Indicated by a sideline in the margin | | | National foreword This British Standard is the English language version of EN 10258 : 1996. It supersedes the requirements for dimensions and shape of cold-rolled narrow strip and cut lengths in BS 1449 : Part 2 : 1983 and in BS 150
5、1 : Part 3 : 1990. Both of these British Standards have been amended. The UK participation in its preparation was entrusted to Technical Committee ISE/30, Stainless steels, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquir
6、ies on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The Briti
7、sh Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or using the Find facility of the BSI Standards Electronic Catalogue. Compliance with
8、a British Standard does not of itself confer immunity from legal obligations. CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and b
9、y any means reserved worldwide for CEN national members. Ref. No. EN 10258 : 1997 E EUROPEAN STANDARDEN 10258 NORME EUROPE ENNE EUROPA ISCHE NORM May 1997 | ICS 77.140.50 Descriptors: Iron- and steel products, cold rolled products, strip, stainless steel, designation, delivery condition, dimensional
10、 tolerances, form tolerances, measurements English version Cold-rolled stainless steel narrow strip and cut lengths Tolerances on dimensions and shape Feuillards ou feuillards coupe s a longueur en acier inoxydable lamine s a froid Tole rances sur les dimensions et la forme Kaltband und kaltband in
11、Sta ben aus nichtrostendem Stahl Grenzabmae und Formtoleranzen This European Standard was approved by CEN on 1997-01-26. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard withou
12、t any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language mad
13、e by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland,
14、 Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Page 2Issue 2, January 1998 EN 10258 : 1997 BSI 1998 | Foreword This European Standard has been prepared by Technical Committee ECISS/TC 23, Steels for heat treatment, alloy steels and free-cut
15、ting steels Qualities, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1997, and conflicting national standards shall be withdrawn at the latest b
16、y November 1997. It is the first edition of a European Standard for tolerances on dimensions and shape for cold-rolled stainless steel narrow strip and cut lengths. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to impleme
17、nt this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Normative references3 3Definitions3 4Designa
18、tion3 5Condition of delivery3 6Tolerances on thickness3 7Tolerances on width3 8Preferred coil inner diameters5 9Tolerances on length5 10Flatness and edge waviness tolerances5 11Tolerances on out-of-squareness6 12Tolerances on edge camber6 13Ordered format (for cut lengths)6 14Measurement6 Annex A(in
19、formative) Bibliography8 Page 3 EN 10258 : 1997 BSI 1997 1 Scope This European Standard applies to cold-rolled stainless, heat resisting and creep resisting steel flat products in thicknesses up to and including 3,0 mm and rolled widths of less than 600 mm delivered as: a) narrow strip (coils with a
20、 rolled width 600 mm), b) slit cold-rolled narrow strip, c) cut lengths obtained from slit cold-rolled narrow strip or cold-rolled narrow strip. It does not apply to cold-rolled stainless, heat resisting and creep resisting steel wide strip and plate/sheet (rolled width $ 600 mm, see EN 10259), or t
21、o cold-rolled products for which there is a specific standard. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed here
22、after. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publications referred to applies. EN 10079Definition of steel produ
23、cts 3 Definitions For the purposes of this European Standard, the definitions given in EN 10079 shall apply. 4 Designation 4.1 Products conforming to this European Standard shall be designated in the following order (see also clause 5): a) type of product (narrow strip or cut length); b) the number
24、of this European Standard (EN 10258); c) nominal thickness in millimetres; d) the letter F or P for products ordered with fine or precision tolerances on thickness; e) nominal width in millimetres; f) the letter F or P for products ordered with fine or precision tolerances on width; g) nominal lengt
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 10258 1997
链接地址:https://www.31doc.com/p-3737126.html