BS-7403-13-1991 ISO-6415-1990.pdf
《BS-7403-13-1991 ISO-6415-1990.pdf》由会员分享,可在线阅读,更多相关《BS-7403-13-1991 ISO-6415-1990.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS 7403-13: 1991 ISO 6415:1990 Full-flow lubricating oil filters for internal combustion engines Part 13: Specification for dimensions of spin-on filters Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:48:39 GMT+00:00 2006, Uncontrolled Copy,
2、 (c) BSI BS 7403-13:1991 This British Standard, having been prepared under the direction of the General Mechanical Engineering Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 29 March 1991 BSI 11-1999 The following BSI references relate t
3、o the work on this standard: Committee reference GME/14 Draft for comment 89/79665 DC ISBN 0 580 19522 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the General Mechanical Engineering Standards Policy Committee (GME/-) to Technical Commi
4、ttee GME/14, upon which the following bodies were represented: British Compressed Air Society Engineering Equipment and Materials Users Association Motor Industry Research Association Society of Environmental Engineers Society of Motor Manufacturers and Traders Ltd. Amendments issued since publicati
5、on Amd. No.DateComments Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:48:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7403-13:1991 BSI 11-1999i Contents Page Committees responsibleInside front cover National forewordii 1Scope1 2Normative references1 3Re
6、quirements1 4Designation2 5Marking3 Figure 1 Connection and sealing surface1 Figure 2 Filter2 Figure 3 Canister base type X Without impressions3 Figure 4 Canister base type Y With grooves Number of grooves: 6 or multiple of 63 Figure 5 Canister base type Z With flats Number of flats: 8, 10, 12, 14,
7、15 or more3 Table 1 Dimensions of connection threads and sealing surface2 Table 2 Filter dimensions2 Publication(s) referred toInside back cover Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:48:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7403-13:1991 i
8、i BSI 11-1999 National foreword This British Standard has been prepared under the direction of the General Mechanical Engineering Standards Policy Committee. It is identical with ISO 6415:1990 “Internal combustion engines Spin-on filters for lubricating oil Dimensions”, published by the Internationa
9、l Organization for Standardization (ISO). BS 7403 will consist of a number of Parts, as follows. Part 1: Method of test for pressure drop/flow characteristics1); Part 2: Method of test for element by-pass component characteristics1); Part 3: Method of test for resistance to high pressure drop and to
10、 elevated temperature1); Part 4: Method of test for initial particle retention efficiency, life and cumulative efficiency (gravimetric method)1); Part 5: Method of test for cold start simulation and hydraulic pulse durability; Part 6: Method of test for static burst pressure; Part 7: Method of test
11、for vibration fatigue; Part 8: Method of test for inlet anti-drain valves; Part 9: Method of test for inlet and outlet anti-drain valves1); Part 10: Method of test for life and cumulative efficiency in the presence of water in oil1); Part 11: Method of test for self-cleaning filters1); Part 12: Meth
12、od of test for particle retention ability and contaminant holding capacity using particle counting1); Part 13: Specification for dimensions of spin-on filters. Other related British Standards are BS 1580-3:1965, which is related to ISO 68:1973, and BS 5346:1976, which is related to ISO 965-1:1980. A
13、 British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a
14、 front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. 1) In preparation. Cross-re
15、ferences International StandardCorresponding British Standard ISO 68:1973BS 3643 ISO metric screw threads ISO 261:1973Part 1:1981 Principles and basic data (Technically equivalent) ISO 965-1:1980 ISO 965-3:1980 Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:
16、48:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 7403-13:1991 BSI 11-19991 1 Scope This International Standard specifies the essential dimensions necessary for interchangeability of spin-on filters of the full flow type for the filtration of lubricating oil for internal combustion engines. It als
17、o gives the designation and marking of these filters. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subjec
18、t to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 68:1973, ISO ge
19、neral purpose screw threads Basic profile. ISO 261:1973, ISO general purpose metric screw threads General plan. ISO 965-1:1980, ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data. ISO 965-3:1980, ISO general purpose metric screw threads Tolerances Part 3: Deviation
20、s for constructional threads. 3 Requirements 3.1 Connection thread and sealing surface NOTE 1The use of filters with unified threads is discouraged to avoid the danger of mis-matching. The dimensions of the male and female connection threads and of the sealing surface are specified in Figure 1 and T
21、able 1. The thread shall conform to ISO 68, ISO 261, ISO 965-1 and ISO 965-3. The sealing surface shall be continuous and free from porosity, scratches and nicks. Figure 1 Connection and sealing surface Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 11:48:39 GM
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-7403-13-1991 ISO-6415-1990 BS 7403 13 1991 ISO 6415 1990
链接地址:https://www.31doc.com/p-3737274.html