BS-AU-175-1B-1983 ISO-3779-1983.pdf
《BS-AU-175-1B-1983 ISO-3779-1983.pdf》由会员分享,可在线阅读,更多相关《BS-AU-175-1B-1983 ISO-3779-1983.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES CONFIRMED MAY 1989 BS AU 175-1b: 1983 ISO 3779:1983 Superseding BS AU 175-1:1979 (Incorporating Amendment No. 1) Vehicle identification numbers (VIN) Part 1b: Specification for content and structure ISO title: Road vehicles Vehicle identification number (VIN) Conte
2、nt and structure UDC 629.11.018.8:003.62 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:49:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 175-1b:1983 This British Standard, having been prepared under the direction of the Automobile Standards Committee,
3、was published under the authority of the Board of BSI and comes into effect on 30 December 1983 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/15 Draft for comment 82/70755 DC ISBN 0 580 13579 9 Committees responsible for this British Standard T
4、he preparation of this British Standard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/15 upon which the following bodies were represented: Caravan Club Department of the Environment (Transport and Road Research Laboratory) Department of Transport Metropolitan
5、 Police National Caravan Council Limited Royal Automobile Club Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:49:45 GMT+00:00 2006, Uncontrol
6、led Copy, (c) BSI BS AU 175-1b:1983 BSI 02-2000i Contents Page Committees responsibleInside front cover National forewordii 1Scope1 2Field of application1 3References1 4Definitions1 5Requirements1 Annex Example3 Table Characters used for designating the year2 Publications referred toInside back cove
7、r Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:49:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 175-1b:1983 ii BSI 02-2000 National foreword This British Standard has been prepared under the direction of the Automobile Standards Committee and is iden
8、tical with ISO 3779:1983 “Road vehicles Vehicle identification number (VIN) Content and structure” prepared by Technical Committee ISO/TC 22, Road vehicles, of the International Organization for Standardization (ISO). This edition of the standard supersedes BS AU 175-1:1979 and extends the field of
9、application to include mopeds. The 1979 edition of the standard is now withdrawn. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with
10、 those used in British Standards; attention is drawn especially to the following. Where the words “International Standard” appear, referring to this standard, they should be read as “British Standard”. The Technical Committee has reviewed the provisions of ISO 3833, to which reference is made in the
11、 text, and has decided that they are acceptable for use in conjunction with this standard. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not
12、of itself confer immunity from legal obligations. Cross-references International StandardCorresponding British Standard ISO 3780:1983BS AU 175 Vehicle identification numbers (VIN) Part 2b:1983 Specification for world manufacturer identifier (WM) codes (Identical) ISO 4030:1983BS AU 175 Vehicle ident
13、ification numbers (VIN) Part 3b:1983 Specification for location and attachment (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may h
14、ave had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:49:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 175-1b:1983 BSI 02-20001 1 Scope This Internationa
15、l Standard specifies the content and structure of a vehicle identification number (VIN) in order to establish, on a world-wide basis, a uniform identification numbering system for road vehicles. 2 Field of application This International Standard applies to motor vehicles, trailers, motorcycles and m
16、opeds as defined in ISO 3833. 3 References ISO 3780, Road vehicles World manufacturer identifier (WMI) code. ISO 3833, Road vehicles Types Terms and definitions. ISO 4030, Road vehicles Vehicle identification number (VIN) Location and attachment. 4 Definitions 4.1 vehicle identification number (VIN)
17、 a structured combination of characters assigned to a vehicle by the manufacturer for identification purposes 4.2 world manufacturer identifier (WMI) the first section of the VIN, designating the manufacturer of the vehicle. The code is assigned to a vehicle manufacturer in order to allow identifica
18、tion of the said manufacturer and, when used in conjunction with the remaining sections of the VIN, ensures uniqueness of the VIN for all vehicles manufactured in the world for a period of 30 years 4.3 vehicle descriptor section (VDS) the second section of the VIN. It provides information describing
19、 the general attributes of the vehicle 4.4 vehicle indicator section (VIS) the last section of the VIN. It is a combination of characters assigned by the manufacturer to distinguish one vehicle from another. This number, in conjunction with the VDS, ensures a unique designation of all vehicles produ
20、ced by each manufacturer for a period of 30 years 4.5 manufacturer a person, firm, or corporation under whose responsibility a vehicle has been assembled to form a unit which is ready for operation; the manufacturer is responsible for the uniqueness of the VIN 4.6 year the calendar year in which the
21、 vehicle was produced or the model year of the vehicle as determined by the manufacturer 4.7 divider a symbol, character or physical border that may be used to separate the sections of the VIN or to define the limits (beginning and end) of the VIN. Dividers should not be capable of being confused wi
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-175-1B-1983 ISO-3779-1983 BS AU 175 1983 ISO 3779
链接地址:https://www.31doc.com/p-3737374.html