BS-EN-10218-2-1997.pdf
《BS-EN-10218-2-1997.pdf》由会员分享,可在线阅读,更多相关《BS-EN-10218-2-1997.pdf(12页珍藏版)》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 10218-2 : 1997 The
2、European Standard EN 10218-2 : 1996 has the status of a British Standard ICS 77.140.70 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Steel wire and wire products General Part 2. Wire dimensions and tolerances Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:01:39 GM
3、T+00:00 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 January 1997 BSI 1997 The following BSI references relate to the work on this
4、 standard: Committee reference ISE/26 Draft for comment 93/301465 DC ISBN 0 580 26402 5 BS EN 10218-2 : 1997 Amendments issued since publication Amd. No.DateText affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee IS
5、E/26, Steel wire, upon which the following bodies were represented: Bicycle Association of GB British Cable Makers Confederation British Iron and Steel Producers Association British Rubber Manufacturers Association British Stainless Steel Association Electricity Association Federation of Wire Rope M
6、anufacturers of Great Britain Forestry Commission Health and Safety Executive National Centre of Tribology Society of Chain Link Fencing Manufacturers Society of Motor Manufacturers and Traders Ltd. Stainless Steel Wire Industry Association Welding Manufacturers Association (BEAMA Ltd.) Woven Wire A
7、ssociation Zinc Development Association Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:01:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 10218-2 : 1997 BSI 1997i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 10218-23 Licensed Copy: sh
8、effieldun sheffieldun, na, Thu Oct 26 04:01:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii BSI 1997 BS EN 10218-2 : 1997 National foreword This British Standard has been prepared by Technical Committee ISE/26 and is the English language version of EN 10218-2 : 1996 Steel and wire products General
9、Part 2: Wire dimensions and tolerances, published by the European Committee for Standardization (CEN). Cross-references Publication referred toCorresponding British Standard EN 10079 : 1992BS EN 10079 : 1993 Definition of steel products Compliance with a British Standard does not of itself confer im
10、munity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 6, an inside back cover and a back cover. Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:01:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CEN European C
11、ommittee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 All rights of reproduction and communication in any form and by any means reserved in all countries to CEN and its members. Ref. No. EN 1021
12、8-2 : 1996 E EUROPEAN STANDARDEN 10218-2 NORME EUROPE ENNE EUROPA ISCHE NORM June 1996 ICS 77.140.70 Descriptors: Iron and steel products, wire, steels, dimensions, dimensional tolerances English version Steel wire and wire products General Part2: Wire dimensions and tolerances Fils et produits tre
13、file s en acier Ge ne ralite s Partie 2: Dimensions et tole rances des fils Stahldraht und Drahterzeugnisse Allgemeines Teil 2: Drahtmae und Toleranzen This European Standard was approved by CEN on 1996-03-07. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate
14、the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists
15、in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies
16、 of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:01:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 102
17、18-2: 1996 BSI 1997 Foreword This European Standard has been prepared by Technical Committee ECISS/TC 30, Steel wires, of which the Secretariat is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at th
18、e latest by December 1996, and conflicting national standards shall be withdrawn at the latest by December 1996. The standard comprises the following Parts: Part 1: Test methods Part 2: Wire dimensions and tolerances According to the CEN/CENELEC Internal Regulations, the national standards organizat
19、ions of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page 1Scope3 2Normative referenc
20、es3 3Definitions3 4Wire diameter tolerances3 5Tolerance on cut lengths3 6Length of wire in coil3 Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:01:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 10218-2: 1996 BSI 1997 1 Scope This Part of this European Standard specifies the toler
21、ances on diameter of round wire and, where applicable, on the length of round wire, cut to length, for bright steel wire (i.e. uncoated), metallic coated steel wire and non-metallic coated steel wire. This standard should not be applied where other requirements for dimensions and tolerances are spec
22、ified in a particular product standard. 2 Normative references This EN incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate place in the text and the publications are listed hereafter. For dated references, subsequent
23、 amendments to or revisions of any of these publications apply to this EN only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 10079Definition of steel products 3 Definitions 3.1 wire For definition of wire see EN
24、 10079. As well as being supplied in the uncoated (bright) condition, wire can also be supplied with metallic or non-metallic coatings or both. The metallic coating can be as a finished coating or as a drawn finished coating. 3.2 cut length A straightened piece of wire cut to a specified length. 4 W
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 10218 1997
链接地址:https://www.31doc.com/p-3737376.html