BS-AU-213-1987 ISO-8703-1986.pdf
《BS-AU-213-1987 ISO-8703-1986.pdf》由会员分享,可在线阅读,更多相关《BS-AU-213-1987 ISO-8703-1986.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 213:1987 ISO 8703:1986 Specification for Calculation of forces on control devices for inertia braking of caravans and light trailers ISO title: Road vehicles Caravans and light trailers Control device for inertia braking Calculation of forces UDC 629.114.3-59
2、2:531.78 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 213:1987 This British Standard, having been prepared under the direction of the Automobile Standards Committee, was published under the authority o
3、f the Board of BSI and comes into effect on 30 January 1987 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/8 Draft for comment 85/73096 DC ISBN 0 580 15697 4 Committees responsible for this British Standard The preparation of this British Standa
4、rd was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/8, upon which the following bodies were represented: Association of Trailer Manufacturers British Compressed Air Society Caravan Club Chief and Assistant Chief Fire Officers Association Consumer Standards Advis
5、ory Committee of BSI Department of Trade and Industry (Vehicle Division) Department of Transport (Highways) National Caravan Council Limited Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank Universit
6、y, London South Bank University, Sat Dec 09 01:57:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 213:1987 BSI 02-2000i Contents Page Committees responsibleInside front cover National forewordii 1Scope1 2Field of application1 3References1 4Symbols and definitions1 5Forces to be taken into accoun
7、t1 Figure 11 Figure 21 Figure 31 Figure 42 Figure 52 Publications referred toInside back cover Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 213:1987 ii BSI 02-2000 National foreword This British Standa
8、rd has been prepared under the direction of the Automobile Standards Committee and is identical with ISO 8703:1986 “Road vehicles Caravans and light trailers Control device for inertia braking Calculation of forces” published by the International Organization for Standardization (ISO). Terminology a
9、nd conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. The comma has
10、 been used as a decimal marker. In British Standards it is current practice to use a full point on the baseline as the decimal marker. Wherever the words “International Standard” appear, referring to this standard, they should be read as “British Standard”. Cross-references. The Technical Committee
11、has reviewed the provisions of ISO 7237 and ISO 7641-1, to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. A related British Standard for ISO 7641-1 is BS AU 210 “Drawbars for caravans and light trailers” Part 1 “Method for cal
12、culation of mechanical strength of steel drawbars”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal ob
13、ligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table
14、on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 213:1987 BSI 02-20001 1 Scope This International Standard specifies, for the manufacturers of control devices for inertia braking
15、, the forces to be taken into account so that sections may be calculated and maximum admissible stresses selected. These forces are not given as a basis for a dynamic test. 2 Field of application This International Standard applies to control devices for inertia braking intended for use on caravans
16、and light trailers1). NOTEFor calculation of the mechanical strength of steel drawbars, see ISO 7641-1. 3 References ISO 7237, Road vehicles Masses and dimensions of caravans Terms and definitions. ISO 7641-1, Road vehicles Caravans and light trailers Calculation of the mechanical strength of the dr
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-213-1987 ISO-8703-1986 BS AU 213 1987 ISO 8703 1986
链接地址:https://www.31doc.com/p-3737384.html