BS-AU-227-1988 ISO-7467-1987.pdf
《BS-AU-227-1988 ISO-7467-1987.pdf》由会员分享,可在线阅读,更多相关《BS-AU-227-1988 ISO-7467-1987.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 227: 1988 ISO 7467:1987 Specification for Dimensions of cylindrical shaft ends and hubs for alternators for commercial vehicles and buses ISO title: Commercial vehicles and buses Cylindrical shaft ends and hubs for alternators UDC 629.1144/.5:629.11.012.64:62
2、9.1.013.11:(083.3) Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 17:00:32 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 227:1988 This British Standard, having been prepared under the direction of the Automobile Standards Committee, was published under the a
3、uthority of the Board of BSI and comes into effect on 31 August 1988 BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference AUE/13 Draft for comment 81/78936 DC ISBN 0 580 16725 9 Committees responsible for this British Standard The preparation of this Brit
4、ish Standard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/13, upon which the following bodies were represented: Department of Transport (Highways) Freight Transport Association Institute of Road Transport Engineers (Incorporated) London Regional Transport Mi
5、nistry of Defence National Bus Company Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 17:00:32 GMT+00:00 2006, Unc
6、ontrolled Copy, (c) BSI BS AU 227:1988 BSI 01-2000i Contents Page Committees responsibleInside front cover National forewordii 1Scope and field of application1 2Reference1 3Dimensions and tolerances1 Figure 1 Shaft end, type 11 Figure 2 Shaft end, type 21 Figure 3 Hub2 Table 12 Table 22 Publication
7、referred toInside back cover Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 17:00:32 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 227:1988 ii BSI 01-2000 National foreword This British Standard has been prepared under the direction of the Automobile Standar
8、ds Committee and is identical with ISO 7467:1987 “Commercial vehicles and buses Cylindrical shaft ends and hubs for alternators”, published by the International Organization for Standardization (ISO). Terminology and conventions. The text of the International Standard has been approved as suitable f
9、or publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. The comma has been used as a decimal marker. In British Standards it is current practice to use a f
10、ull point on the baseline as the decimal marker. Wherever the words “International Standard” appear, referring to this standard, they should be read as “British Standard”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are respon
11、sible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference International StandardCorresponding British Standard ISO 3912:1977BS 4235 Specification for metric keys and keyways Part 2:1977 Woodruff keys and keyways
12、 (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment tabl
13、e on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Fri Dec 08 17:00:32 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 227:1988 BSI 01-20001 1 Scope and field of application This International Standard specifies the dimensional requirements of cy
14、lindrical shaft ends and hubs for interchangeability of alternators. The specifications of this International Standard apply to cylindrical shaft ends (see Figure 1 and Figure 2) and hubs (see Figure 3) for alternators. 2 Reference ISO 3912, Woodruff keys and keyways. 3 Dimensions and tolerances 3.1
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-227-1988 ISO-7467-1987 BS AU 227 1988 ISO 7467 1987
链接地址:https://www.31doc.com/p-3737428.html