BS-AU-211-1987 ISO-8719-1986.pdf
《BS-AU-211-1987 ISO-8719-1986.pdf》由会员分享,可在线阅读,更多相关《BS-AU-211-1987 ISO-8719-1986.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 211:1987 ISO 8719:1986 Specification for Dimensions of four-hole flanges for gear-driven air compressors for commercial vehicles and buses ISO title: Commercial vehicles and buses Four-hole flanges for gear-driven air compressors UDC 629.114.4/.5:621.51.02 18
2、2.22:621 643.412.3 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 211:1987 This British Standard, having been prepared under the direction of the Automobile Standards Committee, was published under the a
3、uthority of the Board of BSI and comes into effect on 30 January 1987 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/13 Draft for comment 84/78525 DC ISBN 0 580 15686 9 Committees responsible for this British Standard The preparation of this Bri
4、tish Standard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/13, upon which the following bodies were represented: Department of Transport (Highways) Freight Transport Association Institute of Road Transport Engineers (Incorporated) London Regional Transport M
5、inistry of Defence National Bus Company Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:59 GMT+00:00 2006, Un
6、controlled Copy, (c) BSI BS AU 211:1987 BSI 02-2000i Contents Page Committees responsibleInside front cover National forewordii 1Scope and field of application1 3Dimensions and tolerances1 4Other specifications3 Figure 1 Four-hole flange configuration1 Figure 2 Dimensions and location of lubricating
7、 oil inlet connection2 Figure 3 Location of lubricating oil outlet outside the centring shoulder3 Table 11 Table 22 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 211:1987 ii BSI 02-2000 National forewor
8、d This British Standard has been prepared under the direction of the Automobile Standards Committee and is identical with ISO 8719:1986 “Commercial vehicles and buses Four-hole flanges for gear-driven air compressors”, published by the International Organization for Standardization (ISO). Terminolog
9、y and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. The comma
10、has been used as a decimal marker. In British Standards it is current practice to use a full point on the baseline as the decimal marker. Wherever the words “International Standard” appear, referring to this standard, they should be read as “British Standard”. NOTETextual error. When adopting the te
11、xt of the International Standard, the textual error given below was discovered. It has been marked in the text and has been reported to ISO in a proposal to amend the text of the International Standard. Clause 3 should be numbered as clause 2 and clause 4 should be numbered as clause 3. A British St
12、andard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cove
13、r, an inside front cover, pages i and ii, pages 1 to 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Ba
14、nk University, Sat Dec 09 01:57:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 211:1987 BSI 02-20001 1 Scope and field of application This International Standard specifies nominal dimensions and tolerances of four-hole flanges for gear-driven air compressors; it also specifies the locations of
15、lubricating oil inlet and outlet connections. This International Standard applies to flanges of gear-driven compressors mounted on reciprocating internal combustion engines for commercial vehicles and buses. 3 1)Dimensions and tolerances 3.1 Dimensions of the four-hole flange The flange configuratio
16、n shall be contained within the area of dimensions P, W, H, A, B and r (see Figure 1 and Table 1). Table 1 1) See national foreword. Figure 1 Four-hole flange configuration Dimensions in millimetres d h8 L 0,2 M 0,2 N 0,2 O 0,2 P max. DW max. H max. ABr max. E 100501007048631113214880151465 + 0,3 0
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-211-1987 ISO-8719-1986 BS AU 211 1987 ISO 8719 1986
链接地址:https://www.31doc.com/p-3737433.html