BS-AU-175-2B-1983 ISO-3780-1983.pdf
《BS-AU-175-2B-1983 ISO-3780-1983.pdf》由会员分享,可在线阅读,更多相关《BS-AU-175-2B-1983 ISO-3780-1983.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES CONFIRMED MAY 1989 BS AU 175-2b:1983 ISO 3780:1983 Superseding BS AU 175-2:1979 Incorporating Amendment No. 1 Vehicle identification numbers (VIN) Part 2b: Specification for world manufacturer identifier (WMI) codes ISO title: Road vehicles World manufacturer ident
2、ifier (WMI) code UDC 629.11.018.8:061.5.004.92 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:49:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 175-2b:1983 BSI 02-2000 ISBN 0 580 13580 2 Committees responsible for this British Standard The preparation o
3、f this British Standard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/15 upon which the following bodies were represented: Caravan Club Department of the Environment (Transport and Road Research Laboratory) Department of Transport Metropolitan Police National
4、 Caravan Council Limited Royal Automobile Club Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments 4832April 1985Indicated by a sideline in the margin Licensed Copy: London South Bank University, London South Bank University, Sat Dec 0
5、9 01:49:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 175-2b:1983 BSI 02-2000i Contents Page Committees responsibleInside front cover National forewordii 1Scope1 2Field of application1 3References1 4Definition1 5General characteristics required1 6Specific characteristics required for the chara
6、cters in the WMI1 7Implementation of WMI code assignments2 National appendix A Guide for the implementation of WMI codes assignments3 Publications referred toInside back cover Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:49:45 GMT+00:00 2006, Uncontrolled
7、Copy, (c) BSI BS AU 175-2b:1983 ii BSI 02-2000 National foreword This British Standard has been prepared under the direction of the Automobile Standards Committee and is identical with ISO 3780:1983 “Road vehicles World manufacturer identifier (WMI) code” prepared by Technical Committee ISO/TC 22, R
8、oad vehicles, of the International Organization for Standardization (ISO). This edition of the standard supersedes BS AU 175-2:1979 and extends the field of application to include mopeds. The 1979 edition of the standard is now withdrawn. Terminology and conventions. The text of the International St
9、andard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. Where the words “International Standard” appear, referring to
10、 this standard, they should be read as “British Standard”. The Technical Committee has reviewed the provisions of ISO 3833, to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. The ISO Guide to which reference is made in clause 7
11、 has not yet been published. As an interim measure, therefore, the procedures for the implementation of WMI codes assignments in the United Kingdom, based on the appropriate parts of the latest draft of the ISO standard, are given in National appendix A to this standard. A British Standard does not
12、purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International StandardCorresponding British Standard
13、 ISO 3779:1983BS AU 175 Vehicle identification numbers (VIN) Part 1b:1983 Specification for content and structure (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been upd
14、ated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:49:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 175-2b:1983 BSI
15、 02-20001 1 Scope This International Standard specifies the content and structure of an identifier in order to establish, on a world-wide basis, the identification of road vehicle manufacturers. This identifier (WMI) is the first section of the vehicle identification number (VIN) described in ISO 37
16、79. 2 Field of application This International Standard applies to motor vehicles, trailers, motorcycles and mopeds as defined in ISO 3833. 3 References ISO 3779, Road vehicles Vehicle identification number (VIN) Content and structure. ISO 3833, Road vehicles Types Terms and definitions. 4 Definition
17、 4.1 world manufacturer identifier (WMI) the first section of the vehicle identification number (VIN), designating the manufacturer of the vehicle. The code is assigned to a vehicle manufacturer in order to allow identification of the said manufacturer and, when used in conjunction with the remainin
18、g sections of the VIN, ensures uniqueness of the VIN for all vehicles manufactured in the world for a period of 30 years NOTE 1For convenience, this definition is repeated from ISO 3780. NOTE 2The term “manufacturer” is defined in ISO 3779. 5 General characteristics required 5.1 The WMI code shall c
19、onsist of three characters. Only the following arabic numerals and roman letters shall be used in the VIN: 1 2 3 4 5 6 7 8 9 0 A B C D E F G H J K L M N P R S T U V W X Y Z (The letters I, O and Q shall not be used.) 5.2 The assigned WMI codes will be maintained and checked by the International Agen
20、cy acting under authorization from ISO: the Society of Automotive Engineers, Inc., (S.A.E.), 400 Commonwealth Drive, Warrendale, PA 15096, USA. 5.3 One or more WMI codes will be assigned to each manufacturer responsible for production of vehicles as specified in ISO 3779 by the National Organization
21、 of that country in which the manufacturer has his headquarters. 5.4 A WMI code assigned to a manufacturer must not be assigned to another manufacturer for at least 30 years after the last year in which the code was used. 6 Specific characteristics required for the characters in the WMI 6.1 First po
22、sition An alphabetic or numeric character designating a geographic area. More than one character may be assigned to a geographic area, based on anticipated needs. 6.2 Second position An alphabetic or numeric character designating a country within a specific geographic area. More than one character m
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-175-2B-1983 ISO-3780-1983 BS AU 175 1983 ISO 3780
链接地址:https://www.31doc.com/p-3737447.html