BS-AU-266-1-1996 ISO-11154-1-1995.pdf
《BS-AU-266-1-1996 ISO-11154-1-1995.pdf》由会员分享,可在线阅读,更多相关《BS-AU-266-1-1996 ISO-11154-1-1995.pdf(18页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 266-1: 1996 ISO 11154-1: 1995 Specification for Roof load carriers Part 1: Roof bars Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:08:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 266-1:1996 This British Standa
2、rd, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 March 1996 BSI 09-1999 The following BSI references relate to the work on this standard: Committee reference AUE/9 Draft for comment 93/7
3、16275 DC ISBN 0 580 25504 2 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee AUE/9, Automobile details and accessories, upon which the following bodies were represented: Automobile Association BSI Testing Services Consumer
4、 Policy Committee of BSI Department of Trade and Industry (Consumer Safety Unit, CA Division) Department of Transport Garage Equipment Association Institute of Trading Standards Administration Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.DateComments
5、 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:08:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 266-1:1996 BSI 09-1999i Contents Page Committees responsibleInside front cover National forewordii 1Scope1 2Normative references1 3Definitions1 4Symbols an
6、d units2 5Requirements2 6Test methods3 7Instructions for use and fitting4 8Marking5 Annex A (normative) Approval/rejection procedure11 Annex B (normative) Tightening torques for fixing roof bars12 Annex C (informative) Determination of allowable additional mass12 Figure 1 Components of roof bar5 Fig
7、ure 2 Components of connecting devices5 Figure 3 Test box6 Figure 4 Test box location and strapping7 Figure 5 Deflection measuring point8 Figure 6 Fl application point9 Figure 7 Flq application point9 Figure 8 Fa and 0,5 Fa application points10 List of referencesInside back cover Licensed Copy: Lond
8、on South Bank University, London South Bank University, Sat Dec 09 02:08:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 266-1:1996 ii BSI 09-1999 National foreword This British Standard has been prepared by Technical Committee AUE/9. It is identical with ISO 11154-1:1995 Road vehicles Roof load
9、 carriers Part 1: Roof bars, published by the International Organization for Standardization (ISO). It is anticipated that additional parts to this standard will be published, as follows, when the corresponding ISO standards have been completed: Part 2: Accessories and attachments to roof bars for s
10、pecial purpose applications; Part 3: Specific purpose roof devices. The Technical Committee has reviewed the provisions of ISO 612:1978 and ISO 1176:1990, to which reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. A British Standard do
11、es not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International StandardCorresponding British S
12、tandard ISO 9227:1990BS 7479:1991 Method for salt spray corrosion tests in artificial atmospheres (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 12, an inside back cover and a back cover. This standard has been updated (see copyr
13、ight date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:08:52 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 266-1:1996 BSI 09-19991 1 Scop
14、e This part of ISO 11154 specifies the minimum safety requirements for roof bars intended for mounting on or above the roofs of passenger cars or light commercial vehicles with a maximum authorized total mass (ISO-M08) as defined in ISO 1176 up to 3,5 t. It applies to general-use roof bars suitable
15、for carrying load, excluding magnetic and vacuum-fixed devices (see note 1). It establishes technical specifications and test methods which offer both the user of roof bars and road users a minimum level of safety when the roof bars are being used in accordance with the manufacturers instructions. M
16、oreover, requirements of ISO 11154 complete the provisions of Directive 74/483/EEC1) concerning these products. NOTE 1The other parts of ISO 11154 are as follows: part 2 covers additional accessories intended to be fitted on general purpose roof bars; part 3 covers specific purpose roof devices; par
17、t 4 covers magnetic and vacuum-fixed devices. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 11154. At the time of publication, the editions indicated were valid. All standards are subject to revision
18、, and parties to agreements based on this part of ISO 11154 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 612:1978, Road vehicles Dimension
19、s of motor vehicles and towed vehicles Terms and definitions. ISO 1176:1990, Road vehicles Masses Vocabulary and codes. ISO 9227:1990, Corrosion tests in artificial atmospheres Salt spray tests. European Commission Directive 79/488/EEC adapting to technical progress Council Directive 74/483/EEC on t
20、he approximation of the laws of the Member States relating to the external projections of motor vehicles, 18 April 1979. 3 Definitions For the purposes of this part of ISO 11154, the following definitions apply. 3.1 roof bar supporting bar with connecting devices which enables a load to be carried o
21、n the roof of a vehicle NOTE 2Generally, roof bars are compatible with the use of additional accessories. NOTE 3Roof bars are fixed on the roof or on original-equipment rails of the vehicle. NOTE 4An example of components of a roof bar is given in Figure 1. 3.2 connecting device set of parts connect
22、ing the supporting bar to the vehicle NOTE 5Examples of connecting device components are given in Figure 1 and Figure 2. 3.3 specific purpose roof device roof device designed for a specific type of load or use 3.4 additional accessory device used in conjunction with the roof bars to carry a specific
23、 type of load 3.5 maximum vehicle roof load, md maximum load capacity permissible on the roof of the vehicle as defined by the vehicle manufacturer 3.6 maximum roof bar set load, mb maximum load capacity permissible on roof bar set as defined by the roof bar manufacturer 3.7 mass of set of roof bars
24、, me total mass of set of roof bars 3.8 theoretical maximum load, mn maximum vehicle roof load md minus mass of set of roof bars me 3.9 actual maximum load, mx theoretical maximum load, mn, or maximum roof bar load, mb, whichever is the lowest 1) European Council Directive 74/483/EEC on the approxim
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-266-1-1996 ISO-11154-1-1995 BS AU 266 1996 ISO 11154 1995
链接地址:https://www.31doc.com/p-3737590.html