BS-AU-50-1.5.4A-1994 ISO-10499-1991.pdf
《BS-AU-50-1.5.4A-1994 ISO-10499-1991.pdf》由会员分享,可在线阅读,更多相关《BS-AU-50-1.5.4A-1994 ISO-10499-1991.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS AU 50-1-5.4a:1994 ISO 10499-1: 1991 Incorporating Amendment No. 1 to BS AU 50-5.4:1994 (Renumbers the BS as BS AU 50-5.4a:1994) not published separately Tyres and wheels Part 1: Tyres Section 5: Industrial vehicle tyres Subsection 5.4a Specification for solid tyres (metric series
2、) for pneumatic tyre rims: Designation, dimensions and marking ICS 53.060; 83.160.99 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1-5.4a:1994 This British Standard, having been prepared under the di
3、rection of the Automobile Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 February 1994 BSI 04-1999 The following BSI references relate to the work on this standard: Committee reference AUE/4 Draft for comment 90/76568 DC ISBN 0 580 22
4、806 1 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Automobile Standards Policy Committee (AUE/-) to Technical Committee AUE/4, upon which the following bodies were represented: Agricultural Engineers Association Automobile Association
5、 British Industrial Truck Association British Pressure Gauge Manufacturers Association British Rubber Manufacturers Association Bus and Coach Council Department of Transport Freight Transport Association Institute of Road Transport Engineers (Inc) Motor Cycle Industrys Association of Great Britain L
6、td. Motor Industry Research Association National Tyre Distributors Association Retread Manufacturers Association Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Ltd. Amendments issued since publication Amd. No.DateComments 10001May 1998Indicated by a sideline in the margin L
7、icensed Copy: London South Bank University, London South Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1-5.4a:1994 BSI 04-1999i Contents Page Committees responsibleInside front cover National forewordii 1Scope1 2Normative references1 3Definitions1 4Tyre des
8、ignations1 5Marking1 6Tyre dimensions2 7Tyre size range2 Table 1 Nominal rim diameter code1 Table 2 Nominal rim width code1 Table 3 Recommended size range and dimensions for solid tyres for pneumatic tyre rims3 List of referencesInside back cover Licensed Copy: London South Bank University, London S
9、outh Bank University, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1-5.4a:1994 ii BSI 04-1999 National foreword This Subsection of this Part of BS AU 50 has been prepared under the direction of the Automobile Standards Policy Committee and is identical with ISO 10499-1:199
10、1 Industrial tyres and rims Rubber solid tyres (metric series) for pneumatic tyre rims Part 1: Designation, dimensions and marking, including Amendment 1, published by the International Organization for Standardization (ISO). Other Parts of this standard are as follows: Part 2: Wheels and rims; Part
11、 3: Valves; Part 4: Rim profiles and dimensions. The Technical Committee has reviewed the provisions of ISO 3877-4 and ISO 4223-2 to which normative reference is made in the text and has decided that they are acceptable for use in conjunction with this standard. A British Standard does not purport t
12、o include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International standardCorresponding British Standard ISO 3739
13、-1:1992BS AU 50 Tyres and wheels Part 1 Tyres Section 5: Industrial vehicle tyres Subsection 5.2:1994 Specification for pneumatic tyres (metric series) on 5 tapered or flat base rims (designation, dimensions and marking) Summary of pages This document comprises a front cover, an inside front cover,
14、pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank U
15、niversity, Sat Dec 09 03:40:01 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 10499-1:1991 BSI 04-19991 1 Scope This International Standard specifies the main requirements, including designations, dimensions and markings, of the metric series of rubber solid tyres for pneumatic tyre rims primarily i
16、ntended for industrial machines for use on prepared surfaces. Rim contours fitting these tyres will be specified in a future part of ISO 3739. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard
17、. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC a
18、nd ISO maintain registers of currently valid International Standards. ISO 3739:1), Industrial tyres and rims Part 1: Pneumatic tyres (metric series) on 5 degrees tapered or flat base rims Designation, dimensions and marking. ISO 3877-4:1984, Tyres, valves and tubes List of equivalent terms Part 4: S
19、olid tyres. ISO 4223-2:1991, Definitions of some terms used in the tyre industry Part 2: Solid tyres. ISO 10499-2:, Industrial tyres and rims Rubber solid tyres (metric series) for pneumatic tyre rims Part 2: Load ratings (To be published). 3 Definitions For definitions of terms relating to solid ty
20、res, see ISO 4223-2; equivalent terms are given in ISO 3877-4. 4 Tyre designations The dimensional and constructional characteristics shall be indicated as follows: 4.1 Nominal section width The nominal section width of the tyre shall be indicated in millimetres, ending either in 0 or 5. 4.2 Nominal
21、 aspect ratio The nominal aspect ratio shall be expressed as a percentage and shall be a multiple of 5. 4.3 Nominal rim diameter code For tyres mounted on existing rims, the code shall be as given in Table 1. Table 1 Nominal rim diameter code 4.4 Nominal rim width code For tyres mounted on existing
22、rims, the code shall be as given in Table 2. Table 2 Nominal rim width code 5 Marking The marking concerning the dimensional and constructional characteristics shall consist of the four-part designation specified in clause 4. The location of the marking of the rim width code may be distinct but shal
23、l be in close proximity to the marking of the other dimensional characteristics. The marking concerning the designation of the service description is specified in ISO 10499-2:. EXAMPLE 225/75 15/6.5 The characteristics of a tyre with the above markings would be as follows: 1) To be published. Nomina
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-50-1.5.4A-1994 ISO-10499-1991 BS AU 50 1.5 1994 ISO 10499 1991
链接地址:https://www.31doc.com/p-3737650.html