BS-EN-10213-4-1996.pdf
《BS-EN-10213-4-1996.pdf》由会员分享,可在线阅读,更多相关《BS-EN-10213-4-1996.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10213-4:1996 Technical delivery conditions for steel castings for pressure purposes Part 4: Austenitic and austenitic-ferritic steel grades The European Standard EN 10213-4:1995 has the status of a British Standard ICS 11.140.30 BS EN 10213-4:1996 This British Standard, having
2、 been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 May 1996 BSI 12-1998 The following BSI references relate to the work on this standard: Committee reference ISE/6 Draft for comment 93/301842 DC ISB
3、N 0 580 25543 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ISE/6, Steel castings, upon which the following bodies were represented: BEAMA Ltd. British Pump Manufacturers Association British Valve and Actuator Manufac
4、turers Association Castings Technology International Engineering Equipment and Materials Users Association Hopkinsons Limited Institute of British Foundrymen Institution of Mechanical Engineers Lloyds Register of Shipping Ministry of Defence Railway Industry Association Amendments issued since publi
5、cation Amd. No.DateComments BS EN 10213-4:1996 BSI 12-1998i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 10213-43 BS EN 10213-4:1996 ii BSI 12-1998 National foreword This British Standard has been prepared under the direction of Technical Committee
6、ISE/6, Steel castings, and is the English language version of EN 10213-4 Technical delivery conditions for steel castings for pressure purposes Part 4: Austenitic and austenitic-ferritic steel grades published by the European Committee for Standardization (CEN). The following Parts of BS EN 10213 su
7、persede BS 1504:1976 which is now withdrawn: A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligatio
8、ns. BS EN 10213-1Technical delivery conditions for steel castings for pressure purposes Part 1:1996 General BS EN 10213-2Technical delivery conditions for steel castings for pressure purposes Part 2:1996 Steel grades for use at room temperature and elevated temperatures BS EN 10213-3Technical delive
9、ry conditions for steel castings for pressure purposes Part 3:1996 Steels for use at low temperatures BS EN 10213-4Technical delivery conditions for steel castings for pressure purposes Part 4:1996 Austenitic and austenitic-ferritic steel grades Summary of pages This document comprises a front cover
10、, an inside front cover, pages i and ii, the EN title page, pages 2 to 6 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. EUROPEAN STANDARD NORME EUROPENNE EUROPISC
11、HE NORM EN 10213-4 December 1995 ICS 77.140.10 Descriptors: Cast steels, structural steels, boilers, pressure equipment, delivery, designation, grades: quality, chemical composition, mechanical properties, austenitic steels, ferritic steels English version Technical delivery conditions for steel cas
12、tings for pressure purposes Part 4: Austenitic and austenitic-ferritic steel grades Conditions techniques de livraison des pices moules en acier pour service sous pression Partie 4: Nuances daciers austnitiques et austno-ferritiques Technische Lieferbedingungen fr Stahlgu fr Druckbehlter Teil 4: Aus
13、tenitische und austenitisch-ferritische Stahlsorten This European Standard was approved by CEN on 1995-10-20. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alter
14、ation. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by transl
15、ation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg
16、, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and communication in any f
17、orm and by any means reserved in all countries to CEN and its members Ref. No. EN 10213-4:1995 E EN 10213-4:1995 BSI 12-1998 2 Foreword This European Standard was prepared by Technical Committee ECISS/TC 31, Steel castings, the secretariat of which is held by AFNOR. The text of the European Standard
18、 EN 10213 Technical delivery conditions for steel castings for pressure purposes consists of 4 Parts: Part 1: General; Part 2: Steel grades for use at room temperature and elevated temperatures; Part 3: Steel grades for use at low temperatures; Part 4: Austenitic and austenitic-ferritic steel grades
19、. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1996, and conflicting national standards shall be withdrawn at the latest by June 1996. According to the Internal Regulations of CEN/CENELEC,
20、 the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword2 1Scope3 2Normative refer
21、ences3 3Requirements3 Annex A (informative)Creep properties6 Table 1 Chemical composition (cast analysis)4 Table 2 Mechanical properties5 Table A.1 Creep resistance6 EN 10213-4:1995 BSI 12-19983 1 Scope According to the general delivery conditions of EN 10213-1 this standard specifies the chemical a
22、nd mechanical requirements to be met under specific inspection of austenitic and austenitic-ferritic grades. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in
23、 the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred t
24、o applies. EN 10213-1, Technical delivery conditions for steel castings for pressure purposes Part 1: General. 3 Requirements 3.1 Chemical composition The cast analysis shall comply with Table 1 (see 7.1 of EN 10213-1 for permissible deviations and for unspecified elements). For chemical analysis on
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 10213 1996
链接地址:https://www.31doc.com/p-3737698.html