BS-EN-13598-2-2009.pdf
《BS-EN-13598-2-2009.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13598-2-2009.pdf(28页珍藏版)》请在三一文库上搜索。
1、BS EN 13598-2:2009 ICS 93.030 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Plastics piping systems for non- pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Specification
2、s for manholes and inspection chambers in traffic areas and deep underground installations Licensed CopyChinese University of Hong Kong, 11/04/2009 07:16, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February
3、2009 BSI 2009 ISBN 978 0 580 54765 2 Amendments/corrigenda issued since publication DateComments BS EN 13598-2:2009 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? Licensed CopyChinese University of Hong Kong, 11/04/2009 07:16, Uncontrolled Copy, (c) BSI BS EN 135
4、98-2:2009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13598-2 January 2009 ICS 93.030 English Version Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications fo
5、r manholes and inspection chambers in traffic areas and deep underground installations Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement enterrs sans pression - Poly(chlorure de vinyle) non plastifi (PVC- U), polypropylne (PP) et polythylne (PE) - Partie
6、2: Spcifications relatives aux regards et aux botes dinspection et de branchement dans les zones de circulation et dans les rseaux enterrs profondment Kunststoff-Rohrleitungssysteme fr erdverlegte drucklose Abwasserkanle und -leitungen - Weichmacherfreies Polyvinylchlorid (PVC-U), Polypropylen (PP)
7、und Polyethylen (PE) - Teil 2: Anforderungen an Einsteigschchte und Kontrollschchte fr Verkehrsflchen und tiefe Erdverlegung This European Standard was approved by CEN on 11 November 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for gi
8、ving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official v
9、ersions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belg
10、ium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR
11、 STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13598-2:2009: E Licensed CopyChinese University
12、 of Hong Kong, 11/04/2009 07:16, Uncontrolled Copy, (c) BSI BS EN 13598-2:2009 EN 13598-2:2009 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms, definitions, symbols and abbreviations . 6 3.1 Terms and definitions . 6 3.2 Abbreviations 8 4 Material . 8 4.1 Material for bases
13、 . 8 4.2 Material for risers and cones 8 4.3 Utilisation of non-virgin materials . 9 4.4 Sealing rings . 9 5 General characteristics . 10 5.1 General . 10 5.2 Colour . 10 6 Geometrical characteristics . 10 6.1 Dimensions . 10 6.2 Additional requirements . 10 7 Mechanical characteristics . 11 8 Physi
14、cal characteristics . 13 9 Performance requirements . 13 9.1 General performance . 13 9.2 Characterization of rotationally moulded product submitted for performance testing 15 10 Marking of inspection chambers and manholes and additional documentation . 15 10.1 Marking of inspection chamber bases an
15、d manhole bases . 15 10.2 Marking of components other than bases 16 10.3 Additional documentation . 16 Annex A (normative) Durability of materials used in specific base designs 18 A.1 General . 18 A.2 Test procedure . 18 A.3 Evaluation of data . 18 A.4 Material characteristics. 18 Annex B (normative
16、) Material requirements for materials used in specific shafts and cones 20 Annex C (normative) Structural integrity of base 22 C.1 General . 22 C.2 Test procedure . 22 C.3 Evaluation of data . 22 Annex D (normative) Impact test on manhole or chamber bases 23 D.1 Test equipment . 23 D.2 Test procedur
17、e . 23 Bibliography 24 Licensed CopyChinese University of Hong Kong, 11/04/2009 07:16, Uncontrolled Copy, (c) BSI BS EN 13598-2:2009 EN 13598-2:2009 (E) 3 Foreword This document (EN 13598-2:2009) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the s
18、ecretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2009, and conflicting national standards shall be withdrawn at the latest by July 2009. Attention is drawn
19、to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This European standard is a supplementary standard for System Standards for plastics piping systems of a
20、particular material for a specified application. There are a number of such System Standards. System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Or
21、ganisation for Standardisation (ISO). They are supported by separate standards on test methods and by European Standards for thermoplastic underground drainage and sewerage systems, to which references are made throughout the System Standard. The System Standards are consistent with general standard
22、s on functional requirements and on recommended practice for installation. This European Standard consists of the following parts under the general title Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and poly
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 13598 2009
链接地址:https://www.31doc.com/p-3737714.html