BS-AU-215-1-1987 ISO-7706-1985.pdf
《BS-AU-215-1-1987 ISO-7706-1985.pdf》由会员分享,可在线阅读,更多相关《BS-AU-215-1-1987 ISO-7706-1985.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 215-1: 1987 ISO 7706:1985 Power take offs (PTOs) Part 1: Specification for dimensions for clearance envelope for commercial road vehicles ISO title: Road vehicles Commercial vehicles Clearance envelope for power take-offs (PTO) UDC 629.114.4:629.113-494 Licen
2、sed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 215-1:1987 This British Standard, having been prepared under the direction of the Automobile Standards Committee, was published under the authority of the Board
3、of BSI and comes into effect on 30 January 1987 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/13 Draft for comment 82/79531 DC ISBN 0 580 15688 5 Committees responsible for this British Standard The preparation of this British Standard was entr
4、usted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/13, upon which the following bodies were represented: Department of Transport (Highways) Freight Transport Association Institute of Road Transport Engineers (Incorporated) London Regional Transport Ministry of Defence Nat
5、ional Bus Company Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:59 GMT+00:00 2006, Uncontrolled Copy, (c) B
6、SI BS AU 215-1:1987 BSI 02-2000i Contents Page Committees responsibleInside front cover National forewordii 0Introduction1 1Scope and field of application1 2Reference1 3General1 4Side-mounted PTO2 5Rear-mounted PTO3 6Designation3 Figure 1 Clearance envelope for side-mounted PTO (Type S)2 Figure 2 Cl
7、earance envelope for rear-mounted PTO (Type Z)3 Publication referred toInside back cover Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 215-1:1987 ii BSI 02-2000 National foreword This Part of BS AU 215
8、has been prepared under the direction of the Automobile Standards Committee and is identical with ISO 7706:1985 “Road vehicles Commercial vehicles Clearance envelope for power take-offs (PTO)”, published by the International Organization for Standardization (ISO). BS AU 215-2 specifies dimensions of
9、 side openings for PTOs. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn espe
10、cially to the following. Wherever the words “International Standard” or “ISO 7706” appear, referring to this standard, they should be read as “British Standard” and “BS AU 215-1” respectively. A British Standard does not purport to include all the necessary provisions of a contract. Users of British
11、 Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference International StandardCorresponding British Standard ISO 7804:1985aBS AU 215 Power take offs (PTOs) Part 2:1987 Specification for di
12、mensions of side openings for commercial road vehicles (Identical) a Since the issue of ISO 7706, ISO 7804 has been published. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back cover. This standard has been up
13、dated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 215-1:1987 BSI
14、 02-20001 0 Introduction It should be appreciated that the requirements of this International Standard did not necessarily reflect current practice at the time of its preparation, but it is recommended that, in the interest of interchangeability for the future, its provisions should be adopted for n
15、ew designs. The clearance envelope which is specified should meet most requirements, but if, for any reason, they are not suitable, the vehicle manufacturer and the PTO manufacturer will have to find an alternative solution which is acceptable to both. 1 Scope and field of application This Internati
16、onal Standard lays down the dimensions of clearance envelopes for regular and heavy duty type truck transmission power take-offs. It is applicable to clearance envelopes required immediately adjacent to the PTO openings or drives on truck transmissions. 2 Reference ISO 7804, Road vehicles Commercial
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-215-1-1987 ISO-7706-1985 BS AU 215 1987 ISO 7706 1985
链接地址:https://www.31doc.com/p-3737787.html