BS-AU-258-1995.pdf
《BS-AU-258-1995.pdf》由会员分享,可在线阅读,更多相关《BS-AU-258-1995.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 258: 1995 Specification for Elasticated straps BS AU 258:1995 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 June 1995 BSI 0
2、6-1999 The following BSI references relate to the work on this standard: Committee reference AUE/9 Draft for comment 94/711641 DC ISBN 0 580 24244 7 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee AUE/9, Automobile detail
3、s and accessories, upon which the following bodies were represented: Automobile Association Consumer Policy Committee of BSI Department of Trade and Industry (Consumer Safety Unit, CA Division) Department of Transport Garage Equipment Association Institute of Trading Standards Administration Petrol
4、Pump Manufacturers Association Society of Motor Manufacturers and Traders Limited The following bodies were also represented in the drafting of the standard, through subcommittees and panels: BSI Testing Services ICE (Ergonomics) Amendments issued since publication Amd. No.DateComments BS AU 258:199
5、5 BSI 06-1999i Contents Page Committees responsibleInside front cover Forewordii 1Scope1 2Construction1 3Product marking1 4Instructions for use1 Annex A (normative) Method of test2 BS AU 258:1995 ii BSI 06-1999 Foreword This British Standard has been prepared by Technical Committee AUE/9. It establi
6、shes a level of performance for elasticated straps with end attachments and attempts to minimize the risk of injury when used. It is however acknowledged that these elasticated straps are not designed for use by children and should be clearly labelled to this effect. The strength requirement propose
7、d has been deduced by evaluating published anthropometric data and arriving at a compromise between the maximum pull strength and repeated pull strengths. It is accepted that elasticated straps are only suited for retaining light loads which have little or no wind resistance and not for any safety c
8、ritical use. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This docume
9、nt comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. BS AU 258:1995 BSI 06-19991 1 Scop
10、e This British Standard specifies requirements for the performance of elasticated straps and their attachments (together referred to in this standard as strap assemblies) throughout a range of temperatures, together with instructions for use and warning markings. The products this standard covers ar
11、e single straps, generally made from braided rubber cord with wire hooks (sometimes known as bungee cords), or multi straps and end attachments (sometimes known as spiders) but may vary in form and material used. They may also be supplied as part of another system, such as luggage carriers or shoppi
12、ng trollies. The standard does not apply to straps or assemblies if the overall length is less than 200 mm unextended. 2 Construction 2.1 The product shall be free from any accessible burrs, sharp edges or other feature that could cause injury in handling. 2.2 If the end attachment is constructed wi
13、th a locking system then any risk of finger entrapment shall be brought to the attention of the user by inclusion within the instructions, (see clause 4). NOTEThe construction of the locking system should be such as to avoid this risk. 2.3 When tested in accordance with Annex A, each elastic strap a
14、ssembly shall sustain a force of 400 N for 1 min. If the strap assembly is manufactured in the form of a spider the centre joining device shall also sustain this force. 2.4 The strap shall stretch to its maximum usable length, as stated by the manufacturer, with the application of a force of less th
15、an or equal to 400 N. 3 Product marking 3.1 The product shall carry a waterproof label which shall be of sufficient strength that it cannot be detached from the strap by a force of up to 70 N applied by finger grip only. The lettering on the label shall be printed red on white using capital letters
16、of 3 mm minimum height for the word “Warning”, 1 mm lower case “x” height for the text and shall comprise the following: “WARNING Do not stretch beyond the maximum usable length of .1) Keep eyes, face and unprotected areas of the body out of possible rebound path. Keep out of reach of children. Do n
17、ot use to secure heavy or large (wind resistant) loads.” In addition the label shall include the following information. a) The UK manufacturers, importers or distributors name or trade mark and address. b) The number and year of this British Standard, i.e. BS AU 258:19952) 3.2 The warnings shall be
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS AU 258 1995
链接地址:https://www.31doc.com/p-3737811.html