BS-EN-10163-1-2004.pdf
《BS-EN-10163-1-2004.pdf》由会员分享,可在线阅读,更多相关《BS-EN-10163-1-2004.pdf(16页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10163-1:2004 Incorporating corrigendum no. 1 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 1: General requirements The European Standard EN 10163-1:2004 has the status of a British Standard ICS 77.140.50 ? BS EN 10163-1:20
2、04 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 16 December 2004 BSI 2007 ISBN 0 580 45121 6 National foreword This British Standard was published by BSI. It is the UK implementation of EN 10163-1:2004, incorporating corrigendum February 2
3、007. It supersedes BS EN 10163-1:1991 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/12, Structural steels. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to in
4、clude all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments 17030 Corrigendum No. 1 30 April 2007Replaces references to
5、 EN 288-2 and EN 288-3 by EN ISO 15609-1 and EN ISO 15614-1 respectively EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10163-1 December 2004 ICS 77.140.50 Supersedes EN 10163-1:1991 English version Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections
6、 - Part 1: General requirements Conditions de livraison relatives ltat de surface des tles, larges plats et profils en acier lamins chaud - Partie 1: Gnralits Lieferbedingungen fr die Oberflchenbeschaffenheit von warmgewalzten Stahlerzeugnissen (Blech, Breitflachstahl und Profile) - Teil 1: Allgemei
7、ne Anforderungen This European Standard was approved by CEN on 4 November 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bi
8、bliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility
9、 of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy
10、, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussel
11、s 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10163-1:2004: E Incorporating corrigendum February 2007 EN 10163-1:2004 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Terms and definitions .4 4 General4 5
12、Classification5 6 Requirements.5 6.1 Depth and affected area of discontinuities.5 6.1.1 Depth.5 6.1.2 Affected area5 6.2 Repair requirements8 6.3 Repair procedures.8 6.3.1 Grinding8 6.3.2 Welding.8 Annex A (informative) Description of most common discontinuities9 Annex B (informative) List of equiva
13、lent terms in foreign languages .11 Annex C (informative) List of national standards which correspond with EURONORMS referenced.12 Bibliography13 EN 10163-1:2004 (E) 3 Foreword This document (EN 10163-1:2004) has been prepared by Technical Committee ECISS/TC 10 “Structural steels Grades and qualitie
14、s”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. This docum
15、ent supersedes EN 10163-1:1991, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 1: General requirements. This document covers the general delivery requirements for the surface condition of hot-rolled steel products such as: plates and wide flats,
16、see Part 2; sections, see Part 3. During the 5 year review of EN 10163-1:1991 the members of ECISS/TC 10 agreed to revise EN 10163- 1:1991. It was asked to bring the text in line with ECISS DOCS N 809 “Iron and steel standardization Model for a product standard”. This document includes a Bibliograph
17、y. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
18、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 10163-1:2004 (E) 4 1 Scope 1.1 This document specifies the general requirements for the surface condition of hot-rolled steel plates, wide flats and sections. I
19、t covers the requirements on the type, the permissible depth and the permissible size of the surface area affected by: discontinuities (imperfections and defects) and repairs by grinding and/or welding. 1.2 This document shall be applied so far as no other requirements for the surface condition exis
20、t in the appropriate material or product standard. The requirements laid down in the appropriate material or product standard shall always prevail. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition
21、 cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 287-1, Qualification test of welders Fusion welding Part 1: Steels. EN 10079:1992, Definition of steel products. EN 10163-2:2004, Delivery requirements for surface condition o
22、f hot-rolled steel plates, wide flats and sections Part 2: Plate and wide flats. EN 10163-3:2004, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 3: Sections. EN ISO 15607, Specification and qualification of welding procedures for metallic materia
23、ls General rules (ISO 15607:2003). NOTE In Annex C EURONORM 19, 53 and 54 are mentioned with corresponding national standards. These EURONORMS are formally withdrawn, but there are no corresponding ENs. Therefore they are not mentioned in this clause. 3 Terms and definitions For the purposes of this
24、 document, the terms and definitions given in EN 10079:1992, EN 10163-2:2004 and EN 10163-3:2004 apply. NOTE For the most common surface discontinuities see the descriptions in Annex A. In Annex B the terms can be found in their respective languages. 4 General Responsibility for the required surface
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 10163 2004
链接地址:https://www.31doc.com/p-3737837.html