BS-EN-1301-2-2008.pdf
《BS-EN-1301-2-2008.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1301-2-2008.pdf(16页珍藏版)》请在三一文库上搜索。
1、BS EN 1301-2:2008 ICS 77.150.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Aluminium and aluminium alloys Drawn wire Part 2: Mechanical properties Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:39, Uncontrolled Copy, (c)
2、 BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2008 BSI 2008 ISBN 978 0 580 56394 2 Amendments/corrigenda issued since publication DateComments BS EN 1301-2:2008 National foreword This British Standard is the UK implementatio
3、n of EN 1301-2:2008. It supersedes BS EN 1301-2:1997 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organizations represented on this committee can be obtained on request to its secretary. This publica
4、tion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:39, Unco
5、ntrolled Copy, (c) BSI BS EN 1301-2:2008 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1301-2 September 2008 ICS 77.150.10Supersedes EN 1301-2:1997 English Version Aluminium and aluminium alloys - Drawn wire - Part 2: Mechanical properties Aluminium et alliages daluminium - Fil tir - Partie 2
6、: Caractristiques mcaniques Aluminium und Aluminiumlegierungen - Gezogene Drhte - Teil 2: Mechanische Eigenschaften This European Standard was approved by CEN on 16 August 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this E
7、uropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (En
8、glish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgar
9、ia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZ
10、ATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1301-2:2008: E Licensed Copy: London South Bank Universi
11、ty, South Bank University, 16/11/2008 11:39, Uncontrolled Copy, (c) BSI BS EN 1301-2:2008 EN 1301-2:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Tensile test.4 Annex A (normative) Rules for rounding11 Bibliography12 Licensed Copy: London South Bank University, South Bank Un
12、iversity, 16/11/2008 11:39, Uncontrolled Copy, (c) BSI BS EN 1301-2:2008 EN 1301-2:2008 (E) 3 Foreword This document (EN 1301-2:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given
13、 the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2009, and conflicting national standards shall be withdrawn at the latest by March 2009. Attention is drawn to the possibility that some of the elements of this document may be th
14、e subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditi
15、ons, then this product shall be removed from the corresponding standard. This document supersedes EN 1301-2:1997. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4 “Wires and drawing stock“ to revise EN 1301-2:1997. Besides editorial adjustments in the text and u
16、pdate of normative references the following changes have been made: Foreword amended; Clause 2: EN 573-3 deleted and included in Bibliography; Tables 1 to 6: Footnotes modified; Table 2: Tempers H13 and H18 added for alloy EN AW-2011 and temper H18 added for alloys EN AW-2014A, EN AW-2017A, EN AW-21
17、17 and EN AW-2024; Table 5: Alloy EN AW-6056 added and temper H18 added for alloys EN AW-6061 and EN AW-6082; Table 6: Temper H18 added. EN 1301 comprises the following parts under the general title: “Aluminium and aluminium alloys Drawn wire“: Part 1: Technical conditions for inspection and deliver
18、y Part 2: Mechanical properties Part 3: Tolerances on dimensions According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Fin
19、land, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: London South Bank University, South Bank University, 16/11/2008
20、 11:39, Uncontrolled Copy, (c) BSI BS EN 1301-2:2008 EN 1301-2:2008 (E) 4 1 Scope This document specifies the mechanical properties of aluminium and aluminium alloy drawn wires for general engineering applications (except aeronautical rivets). It applies to drawn wires, except for electrical or weld
21、ing purposes. It does not apply to drawing stock. The designation of aluminium and aluminium alloys, their chemical composition and the temper designations used in this standard are in accordance with EN 573- 3 and EN 515 respectively. 2 Normative references The following referenced documents are in
22、dispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 515:1993, Aluminium and aluminium alloys Wrought products Temper designations EN 1301-1
23、, Aluminium and aluminium alloys Drawn wire Part 1: Technical conditions for inspection and delivery EN 10002-1, Metallic materials Tensile testing Part 1: Method of test at ambient temperature 3 Tensile test The conditions for the sampling shall be in accordance with EN 1301-1. The testing conditio
24、ns specified in EN 10002-1 shall apply together with the following additional conditions: full section test pieces shall be used; elongation shall be measured on a reference length of 100 mm. Tensile strength shall conform to Tables 1 to 6. NOTE Typical values for proof stress and elongation,are giv
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 1301 2008
链接地址:https://www.31doc.com/p-3738011.html