《BS-EN-1218-5-2004.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1218-5-2004.pdf(54页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1218-5:2004 Incorporating corrigendum no. 1 Safety of woodworking machines Tenoning machines Part 5: One side profiling machines with fixed table and feed rollers or fed by chain The European Standard EN 1218-5:2004 has the status of a British Standard ICS 79.120.10 ? Licensed
2、 Copy: London South Bank University, London South Bank University, Mon May 07 12:28:39 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 1218-5:2004 This British Standard, was published under the authority of the Standards Policy and Strategy Committee on 22 July 2004 BSI 2007 ISBN 0 580 44147 4 Nati
3、onal foreword This British Standard was published by BSI. It is the UK implementation of EN 1218-5:2004, incorporating corrigendum December 2006. The UK participation in its preparation was entrusted to Technical Committee MTE/23, Woodworking machines Safety. A list of organizations represented on t
4、his committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued s
5、ince publication Amd. No. DateComments 17020 Corrigendum No. 1 30 April 2007Addition to the key to Figure A.3, and replacement of Annex ZA Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:28:39 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME
6、 EUROPENNE EUROPISCHE NORM EN 1218-5 July 2004 ICS 79.120.10 English version Safety of woodworking machines - Tenoning machines - Part 5: One side profiling machines with fixed table and feed rollers or fed by chain Scurit des machines pour le travail du bois - Tenonneuses - Partie 5: Machines profi
7、ler sur une face table fixe et avance par rouleaux ou par chane Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen - Teil 5: Einseitige Profiliermaschinen mit festem Tisch und Vorschubrollen oder mit Kettenbandvorschub This European Standard was approved by CEN on 24 Marc
8、h 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtai
9、ned on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secre
10、tariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Por
11、tugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by any means reserv
12、ed worldwide for CEN national Members. Ref. No. EN 1218-5:2004: E Incorporating corrigendum December 2006 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:28:39 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 1218-5:2004 (E) 2 Contents page Foreword4 Introductio
13、n.5 1 Scope6 2 Normative references6 3 Terms and definitions .8 3.1 General8 3.2 Terms8 3.3 Definitions 10 4 List of significant hazards 14 5 Safety requirements and/or measures16 5.1 General16 5.2 Controls16 5.2.1 Safety and reliability of control systems.16 5.2.2 Position of controls.17 5.2.3 Star
14、ting .17 5.2.4 Normal stopping 18 5.2.5 Emergency stop.18 5.2.6 Integrated feed.19 5.2.7 Positioning of tool spindles19 5.2.8 Speed changing.19 5.2.9 Failure of the power supply19 5.2.10 Failure of control circuits19 5.3 Protection against mechanical hazards20 5.3.1 Stability.20 5.3.2 Hazard resulti
15、ng from break-up 20 5.3.3 Tool holder and tool design20 5.3.4 Braking22 5.3.5 Devices to minimise the possibility or the effect of ejection24 5.3.6 Work-piece supports and guides.27 5.3.7 Prevention of access to moving parts.28 5.4 Protection against non-mechanical hazards32 5.4.1 Fire 32 5.4.2 Nois
16、e.32 5.4.3 Emission of chips and dust34 5.4.4 Electricity34 5.4.5 Ergonomics and handling.34 5.4.6 Lighting.34 5.4.7 Pneumatics.34 5.4.8 Hydraulics.34 5.4.9 Radiation.35 5.4.10 Static electricity .35 5.4.11 Errors of fitting.35 5.4.12 Isolation35 5.4.13 Maintenance.35 6 Information for use36 6.1 War
17、ning devices 36 6.2 Marking.36 6.3 Instruction handbook36 Annex A (informative) Examples of safety related electronic control systems39 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:28:39 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 1218-5:2004 (E) 3 Annex
18、 B (normative) Tool spindle dimensional tolerances 43 Annex C (normative) Operating conditions for noise emission measurement 44 C.1 General. 44 C.2 Noise measurements 44 C.2.1 Test conditions 44 C.2.2 Microphone positions. 44 C.2.3 General data sheet 46 Annex D (informative) Safe working practice.
19、49 Bibliography 51 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC 50 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:28:39 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 1218-5:2004 (E
20、) 4 Foreword This document (EN 1218-5:2004) has been prepared by the Technical Committee CEN/TC 142 “Woodworking machines -Safety“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endor
21、sement, at the latest by January 2005, and conflicting national standards shall be withdrawn at the latest by January 2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Direc
22、tive(s). For relationship with EU Directives, see informative Annex ZA, which is an integral part of this document. Organisations contributing to the preparation of this European Standard include European Committee of Woodworking Machinery Manufacturers Association “EUMABOIS“. The European Standards
23、 produced by CEN/TC 142 are particular to woodworking machines and complement the relevant A and B Standards on the subject of general safety (see introduction of EN ISO 12100-1:2003 for a description of A, B and C standards). According to the CEN/CENELEC Internal Regulations, the national standards
24、 organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovak
25、ia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:28:39 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 1218-5:2004 (E) 5 Introduction This document has been prepared to be a harmonised standard to prov
26、ide one means of conforming to the essential safety requirements of the Machinery Directive, and associated EFTA regulations. This document is a type C standard as stated in EN 1070:1998. The machinery concerned and the extent to which hazards, hazardous situations and events covered are indicated i
27、n the scope of this document. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this C type standard take precedence over the provisions of other standards, for machines that have been designed and built in accordance with t
28、he provisions of this type C standard. The requirements of this document are directed to manufacturers and their authorised representatives of one side profiling machines with fixed table and feed rollers or feed chain. It is also useful for designers. This document also includes information which c
29、an be provided by the manufacturer to the user. Common requirements for tooling are given in EN 847-1:1997. Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:28:39 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 1218-5:2004 (E) 6 1 Scope This document specifies t
30、he requirements and/or measures to remove the hazards and/or limit the risks on one side profiling machines with fixed table and feed rollers or feed chain hereinafter referred to as “machines“, where the loading and unloading is manual and where the maximum work-piece height capacity is 200 mm. The
31、 machine is designed to process in one pass one side of solid wood, chip board, fibreboard or plywood and also these materials where they are covered with plastic laminate. The work-piece is fed through the processing units by an integrated feed consisting of rollers or a chain. This document covers
32、 the hazards relevant to these machines as stated in Clause 4. This document does not apply to transportable machines. This document does not deal with any hazards relating to: a) mechanical loading and/ or unloading of the work-piece; or b) a machine being used in combination with any other machine
33、 (as part of a line); or c) use of laser. For Computer Numerically Controlled (CNC) machines this document does not cover hazards related to Electro- Magnetic Compatibility (EMC). NOTE 1 The requirements of this document apply to all machines whatever their method of control e.g. electromechanical a
34、nd/or electronic. This document is primarily directed to machines which are manufactured after the date of publication by CEN. NOTE 2 Single end tenoning machines with sliding table are dealt with in EN 1218-1:1999. Double end tenoning and/or profiling machines fed by chain or chains are dealt with
35、in EN 1218-2. Single end tenoning machines where the tenon is produced only by means of saw-blades are dealt with in EN 1218-3. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For
36、undated references, the latest edition of the referenced document (including any amendments) applies. EN 294:1992, Safety of machinery - Safety distances to prevent danger zones being reached by the upper limbs. EN 418:1992, Safety of machinery - Emergency stop equipment, functional aspects - Princi
37、ples for design. EN 847-1:1997, Tools for woodworking - Safety requirements - Part 1: Milling tools and circular sawblades. EN 954-1:1996, Safety of machinery - Safety related parts of controls systems - Part 1: General principles for design. EN 982:1996, Safety of machinery - Safety requirements fo
38、r fluid power systems and their components Hydraulics. EN 983:1996, Safety of machinery - Safety requirements for fluid power systems and their components Pneumatics. EN 1037:1995, Safety of machinery - Prevention of unexpected start-up. EN 1070:1998, Safety of machinery - Terminology. Licensed Copy
39、: London South Bank University, London South Bank University, Mon May 07 12:28:39 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EN 1218-5:2004 (E) 7 EN 1088:1995, Safety of machinery - Interlocking devices associated with guards - Principles for design and selection. EN 1760-2:2001, Safety of machinery
40、 - Pressure sensitive protection devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars. EN 1837:1999, Safety of machinery - Integral lighting of machines. EN 60204-1:1992, Safety of machinery - Electrical equipment of machines - Part
41、1: General requirements (IEC 60204-1:1992, modified). EN 60529:1991, Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989). EN 60947-4-1 : 1992, Low-voltage switchgear and control gear - Part 4-1: Contactors and motor-starters Electromechanical contactors and motor starters (IEC 60
42、947-4-1:1990) EN 60947-5-1:1997, Low-voltage switchgear and control gear - Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices (IEC 60947-5-1:1990) EN ISO 354:2003, Acoustics - Measurement of sound absorption in a reverberation room (ISO 354:2003) EN
43、ISO 3743-1:1995, Acoustics - Determination of sound power levels of noise sources - Engineering methods for small, moveable sources in reverberant fields - Part 1: Comparison method for hard walled test rooms (ISO 3743- 1:1994). EN ISO 3743-2:1996, Acoustics - Determination of sound power levels of
44、noise sources using sound pressure - Engineering methods for small, moveable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994). EN ISO 3744:1995, Acoustics - Declaration of sound power levels of noise sources using sound pressure - Engineering met
45、hod in an essentially free field over a reflecting plane (ISO 3744:1994). EN ISO 3745:2003, Acoustics - Determination of sound power levels of noise sources - Precision methods for anechoic and semi-anechoic rooms (ISO 3745:2003). EN ISO 3746:1995, Acoustics - Determination of sound power levels of
46、noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:1995). EN ISO 4871:1996, Acoustics - Determination and verification of noise emission values of machinery and equipment (ISO 4871:1996). EN ISO 9614-1:1995, Acoustics - Determ
47、ination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993). EN ISO 11202:1995, Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a workstation and at other specified positions (
48、ISO 11202:1995). EN ISO 11204:1995, Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a workstation and at other specified positions Method requiring environmental corrections (ISO 11204:1995). EN ISO 11688-1:1998, Acoustics - Recommended practic
49、e for the design of low noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995). EN ISO 12100-1:2003, Safety of machinery - Basic concepts, general principles for design - Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles (ISO 12100-2:2003) Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:28:39 GMT+00:00 2007
链接地址:https://www.31doc.com/p-3738148.html