BS-EN-12201-1-2003.pdf
《BS-EN-12201-1-2003.pdf》由会员分享,可在线阅读,更多相关《BS-EN-12201-1-2003.pdf(24页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 12201-1:2003 Plastics piping systems for water supply Polyethylene (PE) Part 1: General The European Standard EN 12201-1:2003 has the status of a British Standard ICS 23.040.01; 91.140.60 ? Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:41:23 GMT+00:00 2006, Uncontr
2、olled Copy, (c) BSI BS EN 12201-1:2003 This British Standard, was published under the authority of the Standards Policy and Strategy Committee on 5 December 2003 BSI 5 December 2003 ISBN 0 580 42983 0 National foreword This British Standard is the official English language version of EN 12201-1:2003
3、. Collectively, EN 12201-1, EN 12201-2 and EN 12201-5 comprise a revision of: BS 6572:1985, Specification for blue polyethylene pipes up to nominal size 63 for below ground use for potable water; BS 6730:1986, Specification for black polyethylene pipes up to nominal size 63 for above ground use for
4、cold potable water. It is intended that these British Standards will be declared obsolescent by March 2005. NOTE 1The UK water industry has indicated that following the publication of this British Standard, the following Water Industry Specification will be declared obsolescent by March 2005 and ret
5、ained for reference where applicable: WIS 4-32-17 (Issue 2), Specification for polyethylene pressure pipes for pressurised water supply and sewerage duties.1) The UK participation in its preparation was entrusted by Technical Committee PRI/88 (previously PRI/61), Plastics piping systems, to Subcommi
6、ttee PRI/88/2 (previously PRI/61/2), Plastics piping systems for pressure applications, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. NOTE 2It was decided not to proceed with the publication of prEN 12201-6, Rec
7、ommended practice for installation, and that existing national practices would be applicable. In the UK, in the absence of a British Standard covering installation, it is the opinion of Technical Committee PRI/88, Plastics piping systems, that reference to the Polyethylene Pipe Systems Manual2), a j
8、oint publication of WRc and BPF Plastic Pipes Group represents established UK practice. NOTE 3Part 7 has been prepared as a CEN/TS, to allow further development. CEN/TS 12201-7 is not mandatory under the Public Procurement Directive. 1)Published by WRc, Swindon. aid enquirers to understand the text;
9、 present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. 2)WRc/BPF PLASTIC PIPES GROUP. Polyethylene Pipe Syste
10、ms Manual. Swindon: WRc, 2002. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 12201-1:2003 X ISB X-0002 i Attention is drawn to the following statutory regulations: Health and
11、Safety at Work etc. Act 1974 and subsequent regulations. Attention is also drawn to any appropriate safety precautions. It is assumed in the drafting of a standard that the execution of its provisions is entrusted to appropriately qualified people. Additional information With reference to the Introd
12、uction and Clause 5, as yet there is no pan-European agreement on water quality requirements, so existing UK regulations remain in force. Regulation 25 of the Water Supply (Water Quality) Regulations 1989 specifies the circumstances in which water undertakers may use products in contact with water s
13、upplies in England and Wales. As part of the UK regulations, all pipes and fittings used to convey drinking water supplies are required to be approved under the provisions of Regulation 25(1) (a) or (b) as appropriate and the Water Regulation Advisory Scheme (WRAS) to ensure that their use will not
14、cause adverse effect on water quality or a risk to health of consumers. In Scotland and Northern Ireland there are similar provisions. These regulations will be revised as necessary to comply with the EU Drinking Water Quality Directive. The UK National Annex NA attached to this standard provides ad
15、ditional information on the selection and installation of piping systems and components in the UK. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International St
16、andards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Stand
17、ard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 18, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when th
18、e document was last issued. Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 12201-1:2003 iiISB -XX2000 Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME E
19、UROPENNE EUROPISCHE NORM EN 12201-1 March 2003 ICS 23.040.01; 91.140.60 English version Plastics piping systems for water supply - Polyethylene (PE) - Part 1: General Systmes de canalisations en plastiques pour alimentation en eau - Polythylne (PE) - Partie 1: Gnralits Kunstoff-Rohrleitungssysteme f
20、r die Wasserversorgung - Polyethylen (PE) - Teil 1: Allgemeines This European Standard was approved by CEN on 27 December 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard
21、 without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other languag
22、e made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hunga
23、ry, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CEN
24、All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12201-1:2003 E Licensed Copy: sheffieldun sheffieldun, na, Sat Oct 28 06:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 12201-1:2003 (E) 2 Contents Foreword 3 Introduction. 4 1Scope
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 12201 2003
链接地址:https://www.31doc.com/p-3738318.html