BS-EN-13126-10-2008.pdf
《BS-EN-13126-10-2008.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13126-10-2008.pdf(16页珍藏版)》请在三一文库上搜索。
1、BS EN 13126-10:2008 ICS 91.190 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Building hardware Requirements and test methods for windows and doors height windows Part 10: Arm-balancing systems Licensed CopyChinese University of Hong Kong, 11/04/2009 07:15, U
2、ncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2009 BSI 2009 ISBN 978 0 580 54620 4 Amendments/corrigenda issued since publication DateComments BS EN 13126-10:2008 National foreword This British Standard is
3、 the UK implementation of EN 13126-10:2008. It supersedes DD CEN/TS 13126-10:2004 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee B/538/4, Building hardware. A list of organizations represented on this committee can be obtained on request to its secre
4、tary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed CopyChinese University of Hong Kong, 11/04/2009 07:15, Uncontro
5、lled Copy, (c) BSI BS EN 13126-10:2008 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13126-10 November 2008 ICS 91.190Supersedes CEN/TS 13126-10:2004 English Version Building hardware - Requirements and test methods for windows and doors height windows - Part 10: Arm-balancing systems Quincai
6、llerie pour le btiment - Exigences et mthodes dessai des ferrures de fentres et portes-fentres - Partie 10: Compas projection Baubeschlge - Beschlge fr Fenster und Fenstertren - Anforderungen und Prfverfahren - Teil 10: Senkklappflgelsysteme This European Standard was approved by CEN on 5 October 20
7、08. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained
8、on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management
9、Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, P
10、oland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and
11、by any means reserved worldwide for CEN national Members. Ref. No. EN 13126-10:2008: E Licensed CopyChinese University of Hong Kong, 11/04/2009 07:15, Uncontrolled Copy, (c) BSI BS EN 13126-10:2008 EN 13126-10:2008 (E) 2 Contents Page Foreword3 1 Scope.5 2 Normative references 5 3 Terms and definiti
12、ons5 4 Classification5 4.1 General5 4.2 Category of use (1 first digit).5 4.3 Durability (2 second digit)5 4.4 Mass (3 third digit)6 4.5 Fire resistance (4 fourth digit).6 4.6 Safety in use (5 fifth digit)6 4.7 Corrosion resistance (6 sixth digit).6 4.8 Security (7 seventh digit) .6 4.9 Application
13、(8-eigth digit)6 4.10 Test sizes (9 ninth digit).6 4.11 Example of classification for arm-balancing systems.7 5 Requirements .7 5.1 General7 5.2 Durability test .7 5.3 Static load test7 6 Test equipment.8 7 Test methods8 7.1 Samples 8 7.2 Durability test procedure.8 7.3 Static load test procedure.9
14、7.4 Corrosion resistance.9 Annex A (informative) Test method diagrams10 Annex B (normative) Flow chart of test procedure12 Licensed CopyChinese University of Hong Kong, 11/04/2009 07:15, Uncontrolled Copy, (c) BSI BS EN 13126-10:2008 EN 13126-10:2008 (E) 3 Foreword This document (EN 13126-10:2008) h
15、as been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at th
16、e latest by May 2009, and conflicting national standards shall be withdrawn at the latest by May 2009. This document supersedes CEN/TS 13126-10:2004. This European Standard is one of a series of European Standards dedicated to building hardware products. A full contribution to the preparation of thi
17、s European Standard has been made by the European manufacturers organization “ARGE” and national standards bodies. EN 13126 Building hardware Requirements and test methods for windows and doors height windows consists of the following parts: Part 1: Requirements common to all types of hardware Part
18、2: Casement fastener handles1) Part 3: Manoeuvring fittings for espagnolette bolts/sliding button1) Part 4: Espagnolette bolts1) Part 5: Devices that restrict the opening of windows1) Part 6: Variable geometry stay hinges (with or without a friction system) Part 7: Finger catches Part 8: Tilt grade
19、10/2: for use only on projecting bottom-hung windows (type J); grade 10/3: for use on both projecting top-hung and bottom hung windows (type H and / or J). 4.10 Test sizes (9 ninth digit) The ninth digit shows the test sizes in accordance with 4.10 of EN 13126-1:2006 as follows: S.W. 2) in mm / S.H.
20、 3) in mm. EXAMPLE 1 200 mm S.R.W. 900 mm S.R.H. The specified size is a test size only. It does not relate to the maximum size to which a window may be fabricated. For instances where an arm-balancing system is available in a range of sizes to suit differing window sizes it shall be tested at the s
21、ize which gives the most severe impact on the hardware, as recommended by the hardware manufacturer. This size is then recorded as the ninth digit. 2) S.R.W. = sash rebate width 3) S.R.H. = sash rebate height Licensed CopyChinese University of Hong Kong, 11/04/2009 07:15, Uncontrolled Copy, (c) BSI
22、BS EN 13126-10:2008 EN 13126-10:2008 (E) 7 4.11 Example of classification for arm-balancing systems Table 1 Example of classification for Arm-balancing Systems 1 2 3 4 56789 - 4 050 0 1 3 - 10/1 1 200/1 200 This denotes arm-balancing systems, which have: Digit 1 category of use - (no requirements);
23、Digit 2 durability grade 4 (15 000 cycles); Digit 3 mass 50 kg; Digit 4 fire resistance grade 0 (no requirements); Digit 5 safety in use grade 1; Digit 6 corrosion resistance grade 3; Digit 7 security - (no requirements); Digit 8 applicable part tested in accordance with part 10 of this standard for
24、 a projecting top hung window; Digit 9 test sizes S.R.W.1) = 1 200 mm, S.R.H.2) = 1 200 mm. 5 Requirements 5.1 General The requirements of arm-balancing systems shall be in accordance with Clause 5 of EN 13126-1:2006. 5.2 Durability test The test specified in 7.2 shall be used to ensure the hardware
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 13126 10 2008
链接地址:https://www.31doc.com/p-3738453.html