BS-EN-10244-2001.pdf
《BS-EN-10244-2001.pdf》由会员分享,可在线阅读,更多相关《BS-EN-10244-2001.pdf(20页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10244-2:2001 Incorporating Corrigendum No. 1 Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 2: Zinc or zinc alloy coatings The European Standard EN 10244-2:2001 has the status of a British Standard ICS 25.220.40; 77.140.65 NO COPYING WITHOUT BSI
2、PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 10244-2:2001 This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the a
3、uthority of the Standards Committee and comes into effect on 15 May 2001 BSI 14 September 2001 ISBN 0 580 37143 3 National foreword This British Standard is the official English language version of EN 10244-2:2001, including corrigendum April 2001. It supersedes BS 443:1982 which is withdrawn. The U
4、K participation in its preparation was entrusted to Technical Committee ISE/26, Steel wire, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or Euro
5、pean publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the nece
6、ssary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on
7、 the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 16, an inside back cov
8、er and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Sidelining in this document indicates the most recent changes by amendment. Amendments issued since publication Amd. No. DateComments 13233 Corrigendum No. 1 14 September 2001 Indicate
9、d by a sideline Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10244-2 March 2001 ICS 25.220.40Incorporating corrigendum April 2001 English version Steel wire and wire products Non-ferrou
10、s metallic coatings on steel wire Part 2: Zinc or zinc alloy coatings Fils et produits trfils en acier Revtements mtalliques non ferreux sur fils dacier Partie 2: Revtements de zinc ou dalliage de zinc Stahldraht und Drahterzeugnisse berzge aus Nichteisenmetall auf Stahldraht Teil 2: berzge aus Zink
11、 und Zinklegierungen This European Standard was approved by CEN on 21 January 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists an
12、d bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibili
13、ty of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands,
14、 Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CENAll rights of exploitation in any form and by any means reserved world
15、wide for CEN national Members. Ref. No. EN 10244-2:2001 E Licensed Copy: sheffieldun sheffieldun, na, Thu Oct 26 04:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 2 EN 10244-2:2001 BSI 14 September 2001 Contents Page Foreword. 3 1Scope . 4 2Normative references . 4 3Terms and definitions. 4 4
16、Coating requirements. 6 4.1Requirements for the coatings material.6 4.2Requirements relating to coating on the wire 6 4.2.1Coating mass. 6 4.2.2Appearance of coating .6 4.2.3Dipping test . 6 4.2.4Special finishes. 8 4.2.5Adherence of coating .8 5Test conditions 10 5.1Selection of samples 10 5.2Deter
17、mination of mass of coating.10 5.2.1General. 10 5.2.2Gravimetric method10 5.2.3Gaseous volumetric method11 5.3Dipping test . 15 5.3.1Principle. 15 5.3.2Reagents 15 5.3.3Preparation of test piece16 5.3.4Performing of the test.16 5.3.5Interpretation of results16 Licensed Copy: sheffieldun sheffieldun,
18、 na, Thu Oct 26 04:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 3 EN 10244-2:2001 BSI 14 September 2001 Foreword This European Standard has been prepared by Technical Committee ECISS/TC 30, Steel wires, the Secretariat of which is held by BSI. This European Standard shall be given the statu
19、s of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2001, and conflicting national standards shall be withdrawn at the latest by September 2001. This European Standard for non-ferrous metallic coating on steel wire is made up of the foll
20、owing parts: Part 1: General principles Part 2: Zinc and zinc alloy coatings Part 3: Aluminium coatings Part 4: Tin coatings Part 5: Nickel coatings Part 6: Copper, bronze and brass coatings According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun
21、tries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Thu Oct
22、 26 04:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Page 4 EN 10244-2:2001 BSI 14 September 2001 1 Scope This part of this European Standard specifies the requirement for coating mass, other properties and testing of zinc and zinc alloy coatings on steel wire and steel wire products of circular
23、or other section. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amend
24、ments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 1179, Zinc and zinc alloys Primary zinc EN 10218-1, St
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 10244 2001
链接地址:https://www.31doc.com/p-3738476.html