BS-EN-10080-2005.pdf
《BS-EN-10080-2005.pdf》由会员分享,可在线阅读,更多相关《BS-EN-10080-2005.pdf(74页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10080:2005 Steel for the reinforcement of concrete Weldable reinforcing steel General The European Standard EN 10080:2005 has the status of a British Standard ICS 77.140.15; 77.140.60; 77.140.65 ? BS EN 10080:2005 This British Standard was published under the authority of the
2、Standards Policy and Strategy Committee on 23 December 2005 BSI 23 December 2005 ISBN 0 580 46804 6 National foreword This British Standard is the official English language version of EN 10080:2005 but will not become current until 01 January 2006. EN 10080 is a candidate harmonized European Standar
3、d and fully takes into account the requirements of the European Commission mandate M115, Reinforcing and prestressing steel (for concrete), given under the EU Construction Products Directive (89/106/EEC), and is intended to lead to CE marking. The date of applicability of EN 10080 as a harmonized Eu
4、ropean Standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to an announcement in the Official Journal of the European Communities. The Commission in consultation with Member States has agreed a transition period for the co-existence of harmonized Europea
5、n Standards and their corresponding national standard(s). It is intended that this period will comprise a period, usually nine months, after the date of availability of the European Standard, during which any required changes to national regulations are to be made, followed by a further period, usua
6、lly of 12 months, for the implementation of CE marking. At the end of this co-existence period, conflicting national standard(s) will be withdrawn. EN 10080 does not include all the requirements to fully specify reinforcing steels. It is intended that EN 10080 should be used in conjunction with a Te
7、chnical Specification, in which the details of the performance characteristics are specified. Within the UK, three standards have been revised for use with EN 10080, these are: BS 4449:2005, Steel for the reinforcement of concrete Weldable reinforcing steel Bar, coil and decoiled product Specificati
8、on BS 4482:2005, Steel wire for the reinforcement of concrete products Specification BS 4483:2005, Steel fabric for the reinforcement of concrete Specification EN 10080:2005 is the subject of transitional arrangements agreed under the Commission mandate. The above standards contain some requirements
9、, which conflict with EN 10080:2005. Based on the transition period of twenty-one months, these standards will be further revised by October 2007, so that they do not conflict with EN 10080. NOTE This date is approximate. Users of this standard should contact BSI Customer Services for confirmation o
10、f revisions. Summary of pages This document comprises a front cover, an inside front cover, page i, a blank page, the EN title page, pages 2 to 69 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Am
11、d. No. DateComments BS EN 10080:2005 i The UK participation in its preparation was entrusted by Technical Committee ISE/9, Steel for concrete reinforcement, to Subcommittee ISE/9/1, Bars, wire and fabric for concrete reinforcement, which has the responsibility to: A list of organizations represented
12、 on this committee can be obtained on request to its secretary. If CE marking is performed, the procedures in Annex ZA will apply. The significance of the CE marking is that the product manufacturer claims compliance with the harmonized requirements given in the normative text of the product standar
13、d. These relate to the essential requirements of the EU Construction Products Directive. Not all product characteristics need necessarily be given on the CE marking, but those product characteristics covered by regulations in force in each EU Member State, where the manufacturer intends that the pro
14、duct will be used, do need to be stated. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” fa
15、cility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. aid enquirers to understand the text; present to the responsible international/European c
16、ommittee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10080 May 2005 ICS 77.140.15; 77.140.60; 77.140.65
17、Supersedes ENV 10080:1995 English version Steel for the reinforcement of concrete - Weldable reinforcing steel - General Aciers pour larmature du bton - Aciers soudables pour bton arm - Gnralits Stahl fr die Bewehrung von Beton - Schweigeeigneter Betonstahl - Allgemeines This European Standard was a
18、pproved by CEN on 21 April 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nation
19、al standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and noti
20、fied to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherl
21、ands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any fo
22、rm and by any means reserved worldwide for CEN national Members. Ref. No. EN 10080:2005: E EN 10080:2005 (E) 2 Contents Page Foreword 3 1 Scope.4 2 Normative references .4 3 Terms and definitions.5 4 Symbols.8 5 Designation .10 5.1 Bar, coil and de-coiled product10 5.2 Welded fabric 10 5.3 Lattice g
23、irders .12 6 Steelmaking and manufacturing processes .13 7 Performance characteristics13 7.1 Weldability and chemical composition .13 7.2 Mechanical properties 14 7.3 Dimensions, mass and tolerances.17 7.4 Bond strength and surface geometry20 7.5 Verification of performance characteristics22 8 Evalu
24、ation of conformity22 8.1 Factory production control 22 8.2 Initial type testing25 8.3 Continuous surveillance of factory production control and audit testing28 8.4 Evaluation, reporting and action30 8.5 Assessment of the long term quality level31 9 Test methods.32 9.1 Bars, coils and de-coiled prod
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 10080 2005
链接地址:https://www.31doc.com/p-3738489.html