BS-AU-207-1986.pdf
《BS-AU-207-1986.pdf》由会员分享,可在线阅读,更多相关《BS-AU-207-1986.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS AU 207:1986 Specification for Dimensions of car radio installation space UDC 629.113.051:621.396.62.005 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 207:1986 This British Standard,
2、having been prepared under the direction of the Automobile Standards Committee, was published under the authority of the Board of BSI and comes into effect on 31 December 1986 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference AUE/9 Draft for comment 81
3、/78343 DC ISBN 0 580 15347 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/9, upon which the following bodies were represented: Automobile Association British Friction M
4、aterials Council Consumer Standards Advisory Committee of BSI Department of Trade and Industry (Consumer Safety Unit, C S Division) Department of Transport (Highways) Garage Equipment Association Health and Safety Executive Home Office Institute of Trading Standards Administration Motor Agents Assoc
5、iation Limited Motor Cycle Association of Great Britain Petrol Pump Manufacturers Association Royal Automobile Club Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank Univ
6、ersity, Sat Dec 09 01:57:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 207:1986 BSI 02-2000i Contents Page Committees responsibleInside front cover Forewordii 1Scope1 2Dimensions of installation space and fixing areas1 3Dimensions and position of port1 Appendix A Recommendations for installati
7、on3 Figure 1 Dimensions for installation by front fixing1 Figure 2 Dimensions for installation by lateral fixing1 Figure 3 Dimensions for installation by additional rear fixing and for a port2 Publication referred toInside back cover Licensed Copy: London South Bank University, London South Bank Uni
8、versity, Sat Dec 09 01:57:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 207:1986 ii BSI 02-2000 Foreword BS AU 207 was prepared under the direction of the Automobile Standards Committee. It is similar to but not identical with ISO 7736 “Road vehicles Car radio for front installation Installati
9、on space including connections”, published by the International Organization for Standardization (ISO). Changes have been made to Figure 1 and Figure 2 of that International Standard to permit fitment of some existing car radios and future equipment. The minimum lateral fixing installation dimension
10、 has been increased from 188 mm minimum to 189.5 mm minimum. The radius “R3 max.” in the International Standard has been amended to “R4 max.”. The dimension “5 1” in the International Standard has been changed to “5.5 0.5”. A British Standard does not purport to include all the necessary provisions
11、of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an insid
12、e back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 01:57:58 GMT+00:
13、00 2006, Uncontrolled Copy, (c) BSI BS AU 207:1986 BSI 02-20001 1 Scope This British Standard specifies the dimensions for the installation space and fixing areas required by car radio equipment and its electrical connections, including car radio equipment which is combined with other sound reproduc
14、tion equipment. General recommendations for installation spaces are given in Appendix A. 2 Dimensions of installation space and fixing areas 2.1 The dimensions for installation by front fixing shall be as shown in Figure 1. 2.2 The dimensions for installation by lateral fixing shall be as shown in F
15、igure 2. NOTEFront fixing or lateral fixing or a combination of front and lateral fixing may be used. 2.3 The dimensions for installation by additional rear fixing shall be as shown in Figure 3. NOTERear fixing may be provided in addition to the front and lateral fixings. 3 Dimensions and position o
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS AU 207 1986
链接地址:https://www.31doc.com/p-3738533.html