BS-AU-216-1-1987 ISO-7309-1985.pdf
《BS-AU-216-1-1987 ISO-7309-1985.pdf》由会员分享,可在线阅读,更多相关《BS-AU-216-1-1987 ISO-7309-1985.pdf(8页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 216-1: 1987 ISO 7309:1985 Hydraulic brake systems using petroleum base brake fluids for road vehicles Part 1: Specification for petroleum base reference fluid ISO title: Road vehicles Hydraulic braking systems ISO reference petroleum base fluid UDC 629.113-59
2、2.2:665.767:621.22 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:04:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 216-1:1987 This British Standard, having been prepared under the direction of the Rubber Standards Committee, was published under the aut
3、hority of the Board of BSI and comes into effect on 31 July 1987 BSI 02-2000 The following BSI references relate to the work on this standard: Committee reference RUM/40 Draft (ref. 83/36744) announced in BSI News August 1983 ISBN 0 580 15968 X Committees responsible for this British Standard The pr
4、eparation of this British Standard was entrusted by the Rubber Standards Committee (RUM/-) to Technical Committee RUM/40, upon which the following bodies were represented: British Chemical Distributors and Traders Association Limited British Rubber Manufacturers Association Chemical Industries Assoc
5、iation Department of Transport (Highways) Institute of Petroleum London Regional Transport Malaysian Rubber Producers Research Association Ministry of Defence Society of Motor Manufacturers and Traders Limited Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London So
6、uth Bank University, London South Bank University, Sat Dec 09 02:04:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 216-1:1987 BSI 02-2000i Contents Page Committees responsibleInside front cover National forewordii 1Scope and field of application1 2References1 3Composition1 4Physical and chemica
7、l characteristics required1 Table 11 Table 21 Publications referred toInside back cover Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:04:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 216-1:1987 ii BSI 02-2000 National foreword This Part of this Britis
8、h Standard has been prepared under the direction of the Rubber Standards Committee in consultation with the Automobile Standards Committee. It is identical with ISO 7309:1985 “Road vehicles Hydraulic braking systems ISO reference petroleum base fluid”, published by the International Organization for
9、 Standardization (ISO). This is Part 1 of BS AU 216 which covers components for vehicle braking systems using petroleum base fluids. It is intended to issue other Parts specifying petroleum base brake fluid, boots, cups and seals for use in the braking system. The associated British Standard BS AU 1
10、74 “Hydraulic brake systems, using non-petroleum base brake fluids, for road vehicles” specifies similar components for vehicle braking systems using non-petroleum base fluids. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a Brit
11、ish Standard without deviation. Some terminology and certain conventions are not identical with those used in British Standards; attention is drawn especially to the following. The comma has been used as a decimal marker. In British Standards it is current practice to use a full point on the baselin
12、e as the decimal marker. Wherever the words “International Standard” appear, referring to this standard, they should be read as “Part of this British Standard”. The Technical Committee has reviewed the provisions of ISO 3104, ISO 3405 and ISO 6618, to which reference is made in the text and has deci
13、ded that they are acceptable for use in conjunction with this standard. ISO 3104:1976 and ISO 3405:1975 are related to BS 2000 “Methods of test for petroleum and its products” Part 71:1982 “Kinematic viscosity of transparent and opaque liquids and calculation of dynamic viscosity” and Part 123:1985
14、“Distillation of petroleum products”, respectively. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal ob
15、ligations. Cross-references International StandardCorresponding British Standard ISO 2592:1973BS 4689:1980 Method for determination of flash and fire points of petroleum products: Cleveland open cup method (Identical) ISO 3016:1974BS 2000 Methods of test for petroleum and its products Part 15:1982 P
16、our point of petroleum oils (Technically equivalent) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 and 2, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This
17、 will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:04:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 216-1:1987 BSI 02-20001 1 Scope and field of application This International Standard sp
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-216-1-1987 ISO-7309-1985 BS AU 216 1987 ISO 7309 1985
链接地址:https://www.31doc.com/p-3738534.html