BS-EN-15091-2006.pdf
《BS-EN-15091-2006.pdf》由会员分享,可在线阅读,更多相关《BS-EN-15091-2006.pdf(50页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 15091:2006 Incorporating corrigendum no. 1 Sanitary tapware Electronic opening and closing sanitary tapware The European Standard EN 15091:2006 has the status of a British Standard ICS 91.140.70 ? Licensed Copy: London South Bank University, London South Bank University, Fri F
2、eb 15 08:05:36 GMT+00:00 2008, Uncontrolled Copy, (c) BSI BS EN 15091:2006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2007 BSI 2007 ISBN 978 0 580 60824 7 National foreword This British Standard is the UK implementation of EN
3、 15091:2006, incorporating corrigendum October 2007. The start and finish of text introduced or altered by corrigendum is indicated in the text by tags . Text altered by CEN corrigendum October 2007 is indicated in the text by . The UK participation in its preparation was entrusted to Technical Comm
4、ittee B/504, Water supply. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard
5、 cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments 17514 Corrigendum No. 1 31 December 2007 See national foreword Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 08:05:36 GMT+00:00 2008, Uncontrolled Copy, (
6、c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15091 December 2006 ICS 91.140.70 English Version Sanitary tapware - Electronic opening and closing sanitary tapware Robinetterie sanitaire - Robinet sanitaire ouverture et fermeture lectronique Sanitrarmaturen - Sanitramaturen mit elektron
7、ischer ffnungs- und Schliefunktion This European Standard was approved by CEN on 4 November 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to
8、-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under
9、the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Icela
10、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de
11、Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15091:2006: E Incorporating corrigendum October 2007 Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 08:05:36 GM
12、T+00:00 2008, Uncontrolled Copy, (c) BSI EN 15091:2006 (E) 2 Contents Page Foreword5 Introduction.6 1 Scope 7 2 Normative references9 3 Terms and definitions .11 4 General requirements and testing .11 4.1 Marking.11 4.2 Materials .12 4.3 Functions12 4.4 Protection against pollution.12 4.5 Electric c
13、haracteristics and requirements12 4.6 Leaktightness characteristics14 4.7 Pressure resistance characteristics15 5 Requirements and testing for tapware17 5.1 Scope 17 5.2 Dimensional characteristics.17 5.3 Hydraulic characteristics25 5.4 Water hammer32 5.5 Endurance 33 5.6 Acoustic characteristics .3
14、4 6 Requirements and testing for flushing valves for urinals.36 6.1 Scope 36 6.2 Definitions 36 6.3 Classification of flushing urinal valves.36 6.4 Designation 36 6.5 Dimensional characteristics.37 6.6 Hydraulic characteristics38 6.7 Measurement of water hammer for urinal flushing valves.38 6.8 Mech
15、anical endurance 39 7 Requirements and testing for flushing valves for WCs.40 7.1 Scope 40 7.2 Definitions 40 7.3 Classification41 7.4 Dimensional characteristics.41 7.5 Hydraulic characteristics43 7.6 Principle and verification of atmospheric pipe interrupters of WC flushing valves.43 7.7 Mechanica
16、l endurance 43 7.8 Acoustic characteristics .44 Annex A (normative) Recommendation for the design of pressure take-off tees45 Bibliography47 Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 08:05:36 GMT+00:00 2008, Uncontrolled Copy, (c) BSI EN 15091:2006 (E) 3 F
17、igures contents Figure 1 Type 1 - Supply system with a pressure range of (0,05 to 1,0) MPa (0,5 to 10) bar.8 Figure 2 Type 2 - Supply system with a pressure range of (0,01 to 1,0) MPa (0,1 to 10) bar.9 Figure 3 Tap with visible body for horizontal surface .18 Figure 4 Threaded inlets of taps with vi
18、sible body for mounting on vertical surfaces19 Figure 5 Tapware with inlets and outlets aligned.19 Figure 6 Tapware with inlets and outlets at right angles.20 Figure 7 Mixing valves for horizontal mounting threaded inlet21 Figure 8 Mixing valves for horizontal mounting, stud connection.21 Figure 9 M
19、ixing valves with straight fittings.22 Figure 10 Mixing valve with excentric unions.23 Figure 11 Mixing valve with captive nuts.24 Figure 12 Mixer with opposed inlets25 Figure 13 Supply circuits26 Figure 14 Test circuits for tapware intended for Type 1 water supply systems.28 Figure 15 Mounting of m
20、ixing valves.29 Figure 16 Flow rate test apparatus for taps intended for type 2 supply systems.30 Figure 17 Test rig for water hammer test32 Figure 18 Top-entry urinal flushing valve .37 Figure 19 Side-entry urinal flushing valve 37 Figure 20 Side-entry WC flushing valves43 Figure 21 Top-entry WC fl
21、ushing valves.43 Figure A.1 Examples of pressure take-off tees.45 Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 08:05:36 GMT+00:00 2008, Uncontrolled Copy, (c) BSI EN 15091:2006 (E) 4 Tables Contents Table 1 Identification of the clauses of this standard6 Tabl
22、e 2 Conditions of use .7 Table 3 Performance characteristics to be noted if used outside the recommended operating range .7 Table 4 Summary of leaktightness tests .15 Table 5 Dimensions18 Table 6 Dimensions of threaded inlets 19 Table 7 Dimensions of threads.20 Table 8 Dimensions of mixers 21 Table
23、9 Dimensions24 Table 10 Dimensions of pipework28 Table 11 Flow rates and test pressures according to application31 Table 12 Acoustic groups .35 Table 13 Classes of flow rate35 Table 14 Classification 36 Table 15 Threads37 Table 16 Flow rate38 Table 17 Dimension of the supply pipe39 Table 18 Threads
24、and outlet pipe.41 Table 19 Permitted thread lengths .41 Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 08:05:36 GMT+00:00 2008, Uncontrolled Copy, (c) BSI EN 15091:2006 (E) 5 Foreword This document (EN 15091:2006) has been prepared by Technical Committee CEN/T
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 15091 2006
链接地址:https://www.31doc.com/p-3738655.html