BS-AU-203A-1988 ISO-7653-1985.pdf
《BS-AU-203A-1988 ISO-7653-1985.pdf》由会员分享,可在线阅读,更多相关《BS-AU-203A-1988 ISO-7653-1985.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 203a:1988 ISO 7653:1985 Specification for Dimensions of couplings between power take offs (PTOs) and ancillary driven units on commercial road vehicles ISO title: Road vehicles Commercial vehicles Couplings between power take-offs (PTO) and ancillary driven u
2、nits UDC 629.113 44.013.5:621.824 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:05:05 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 203a:1988 This British Standard, having been prepared under the direction of the Automobile Standards Committee, was publi
3、shed under the authority of the Board of BSI and comes into effect on 29 February 1988 BSI 10-1999 The following BSI references relate to the work on this standard: Committee reference AUE/13 Draft for comment 82/78280 DC ISBN 0 580 16509 4 Committees responsible for this British Standard The prepar
4、ation of this British Standard was entrusted by the Automobile Standards Committee (AUE/-) to Technical Committee AUE/13 upon which the following bodies were represented: Department of Transport (Highways) Freight Transport Association Ltd. Institute of Road Transport Engineers (Incorporated) London
5、 Regional Transport National Bus Company National Freight Corporation (NFC) Ltd. Road Haulage Association Ltd. Society of Motor Manufacturers and Traders Ltd. Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: London South Bank University, London South Bank University,
6、Sat Dec 09 02:05:05 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 203a:1988 BSI 10-1999i Contents Page Committees responsibleInside front cover National forewordii 1Scope and field of application1 2References1 3Specifications1 4Designation1 Figure 1 Type A indirect coupling PTO side2 Figure 2 Typ
7、e D direct coupling3 Publications referred toInside back cover Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:05:05 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 203a:1988 ii BSI 10-1999 National foreword This British Standard has been prepared under the
8、direction of the Automobile Standards Committee and is identical with ISO 7653:1985 (as corrected and reprinted in April 1986) “Road vehicles Commercial vehicles Couplings between power take-offs (PTO) and ancillary driven units”, published by the International Organization for Standardization (ISO)
9、. This edition of the standard supersedes BS AU 203:1985, which is withdrawn. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with tho
10、se used in British Standards; attention is drawn especially to the following. The comma has been used as a decimal marker. In British Standards it is current practice to use a full point on the baseline as the decimal marker. Wherever the words “International Standard” appear, referring to this stan
11、dard, they should be read as “British Standard”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal oblig
12、ations. Cross-references International StandardCorresponding British Standard BS AU 214 Gearbox flanges ISO 7646:1986aPart 2:1988 Specification for dimensions for type A gearbox flanges for commercial vehicles and buses (Identical) ISO 7647:1986aPart 3:1988 Specification for dimensions for type S ge
13、arbox flanges for commercial vehicles and buses (Identical) a Since ISO 7646 and ISO 7647 are now published, footnote 1) to clause 2 is no longer applicable. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4, an inside back cover and a back c
14、over. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:05:05 GMT+00:00 2006, Uncontrolled Cop
15、y, (c) BSI BS AU 203a:1988 BSI 10-19991 1 Scope and field of application This International Standard lays down the dimensions of couplings between power take-offs (PTO) and ancillary driven units mounted on commercial vehicles, such as hydraulic pumps, etc. This International Standard applies to anc
16、illary equipment of commercial vehicles that require a hydraulic or mechanical power system and that take power off the main drive line of the vehicle. 2 References ISO 7646, Road vehicles Gearbox flanges for commercial vehicles and buses Type A1). ISO 7647, Road vehicles Gearbox flanges for commerc
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-203A-1988 ISO-7653-1985 BS AU 203 1988 ISO 7653 1985
链接地址:https://www.31doc.com/p-3738671.html