BS-EN-13555-2004.pdf
《BS-EN-13555-2004.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13555-2004.pdf(32页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13555:2004 Flanges and their joints Gasket parameters and test procedures relevant to the design rules for gasketed circular flange connections The European Standard EN 13555:2004 has the status of a British Standard ICS 23.040.60; 23.040.80 ? Licensed Copy: sheffieldun sheffi
2、eldun, na, Sun Oct 29 09:54:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 13555:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 13 December 2004 BSI 13 December 2004 ISBN 0 580 45051 1 National foreword This British Standard is the
3、 official English language version of EN 13555:2004. The UK participation in its preparation was entrusted to Technical Committee PSE/2, Jointing materials and compounds, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretar
4、y. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue
5、 or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the t
6、ext; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front c
7、over, an inside front cover, the EN title page, pages 2 to 28, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na,
8、 Sun Oct 29 09:54:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13555 December 2004 ICS 23.040.60; 23.040.80 English version Flanges and their joints - Gasket parameters and test procedures relevant to the design rules for gasketed circular flange
9、 connections Brides et leurs assemblages - Paramtres de joints et modes opratoires dessai relatifs aux rgles de calcul des assemblages brides circulaires avec joint Flansche und ihre Verbindungen - Dichtungskennwerte und Prfverfahren fr die Anwendung der Regeln fr die Auslegung von Flanschverbindung
10、en mit runden Flanschen und Dichtungen This European Standard was approved by CEN on 27 October 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. U
11、p-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation un
12、der the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I
13、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stass
14、art, 36 B-1050 Brussels 2004 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13555:2004: E Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:54:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13555:2004 (E) 2 Contents Page
15、Foreword3 Introduction.4 1 Scope 5 2 Normative references5 3 Notations 6 4 List of gasket parameters .7 5 Definitions 7 6 Test equipment 8 7 Test specimens10 8 Test procedures.11 9 Report details.19 Annex A (informative) Generalised test rig schematic20 Annex B (informative) Test rig schematic for c
16、ompression and compression creep tests21 Annex C (informative) Test rig schematic for ambient temperature leakage measurement.22 Annex D (informative) Schematic of leakage rig allowing use of interchangeable face plate 23 Annex E (informative) Transferability of measured leakage rates to service con
17、ditions24 Annex F (informative) Relationship of gasket parameters of this standard with those from PVRC method25 Annex G (informative) The measurement of the sealing parameter Qsmin (L) after long term service simulating exposure to elevated temperature26 Bibliography28 Licensed Copy: sheffieldun sh
18、effieldun, na, Sun Oct 29 09:54:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13555:2004 (E) 3 Foreword This document (EN 13555:2004) has been prepared by Technical Committee CEN/TC 74 “Flanges and their joints“, the secretariat of which is held by DIN. This European Standard shall be given the s
19、tatus of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and conflicting national standards shall be withdrawn at the latest by June 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the fol
20、lowing coun- tries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Esto- nia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain,
21、Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:54:41 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13555:2004 (E) 4 Introduction This document provides the test procedures to allow the generation of the gasket parameters to enable the design equatio
22、ns established in EN 1591-1 to be employed. The same test procedures may be used for “Type Testing“ of gaskets and gasket materials. These procedures are not for routine quality control purposes. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 09:54:41 GMT+00:00 2006, Uncontrolled Copy, (c) B
23、SI EN 13555:2004 (E) 5 1 Scope This document specifies the design parameters of gaskets and gasket materials required by EN 1591-1 and pro- vides the test procedures for establishing the values of these parameters for inclusion in ENV 1591-2. The testing procedures given might be applicable to gaske
24、ts of other shapes and dimensions but this shall be indi- cated in the report. Gaskets which are wholly based upon elastomers, or based upon elastomer with the inclusion of particulate fillers or particulate reinforcement, are beyond the scope of this document. 2 Normative references The following r
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 13555 2004
链接地址:https://www.31doc.com/p-3739015.html