《BS-EN-13553-2002.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13553-2002.pdf(16页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13553:2002 Resilient floor coverings Polyvinyl chloride floor coverings for use in special wet areas Specification The European Standard EN 13553:2002 has the status of a British Standard ICS 97.150 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW License
2、d Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 13553:2002 This British Standard, having been prepared under the direction of the Materials and Chemicals Sector Policy and Strategy Committee, was published under the authority of the Standards
3、 Policy and Strategy Committee on 20 May 2002 BSI 20 May 2002 ISBN 0 580 39742 4 National foreword This British Standard is the official English language version of EN 13553:2002. The UK participation in its preparation was entrusted to Technical Committee PRI/60, Resilient floor coverings, which ha
4、s the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the
5、 section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applica
6、tion. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related in
7、ternational and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 13 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendm
8、ents issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13553 April 2002 ICS 97.150 English version Resilient floor coverings - Polyvinyl chlori
9、de floor coverings for use in special wet areas - Specification Revtements de sol rsilients - Revtements de sol base de polychlorure de vinyle pour zones humides spciales - Spcifications Elastische Bodenbelge - Polyvinylchlorid-Bodenbelge zur Anwendung in besonderen Nassrumen - Spezifikation This Eu
10、ropean Standard was approved by CEN on 23 February 2002. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical reference
11、s concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its
12、 own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, S
13、pain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2002 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN nationa
14、l Members. Ref. No. EN 13553:2002 E Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13553:2002 (E) 2 Contents page Foreword3 1Scope 4 2Normative references 4 3Terms and definitions4 4Requirements.5 5Marking .6 Annex A (normative) Watertig
15、htness test7 Annex B (informative) Choice of floor covering category10 Annex C (informative) Installation 11 Annex D (informative) Determination of elongation at break as an optional property .12 Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) B
16、SI EN 13553:2002 (E) 3 Foreword This document EN 13553 has been prepared by Technical Committee CEN/TC 134 “Resilient and textile floor coverings“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical
17、text or by endorsement, at the latest by October 2002, and conflicting national standards shall be withdrawn at the latest by October 2002. Requirements for enhanced slip resistance of products other than those of EN 649 and EN 651 are under development and will be incorporated in this document, by
18、revision, when available. Annex A is normative, and the annexes B, C and D are informative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Fin
19、land, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13553:2002 (E) 4 1 Scope This Eur
20、opean standard specifies the minimum additional characteristics which are necessary for: ? polyvinyl chloride floor coverings in roll form according to EN 649, and ? polyvinyl chloride floor coverings with foam backing in roll form to EN 651 to be installed satisfactorily in special wet areas to for
21、m a watertight installation with a long life. It specifies two categories (A and B) for use on different substrates. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate
22、places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication
23、referred to applies (including amendments). EN 428, Resilient floor coverings Determination of overall thickness. EN 429, Resilient floor coverings Determination of the thickness of layers. EN 435, Resilient floor coverings Determination of flexibility. EN 649, Resilient floor coverings Homogenous a
24、nd heterogeneous polyvinylchloride floor coverings Specification. EN 651, Resilient floor coverings Polyvinyl chloride floor coverings with foam layer Specification. EN 661, Resilient floor coverings Determination of the spreading of water. EN 684:1995, Resilient floor coverings Determination of sea
25、m strength. EN 12466, Resilient floor coverings Vocabulary. 3 Terms and definitions For the purposes of this European Standard the terms and definitions of EN 12466 and the following term and definition apply: 3.1 special wet area area where floors are designed to be frequently or permanently wet an
26、d equipped with a floor-based drain, for example bathrooms with free-standing tubs, shower rooms without partitions Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13553:2002 (E) 5 4 Requirements 4.1 General requirements Products covered
27、by this standard shall conform to the requirements of EN 649 or EN 651. 4.2 Additional performance requirements Floor coverings conforming to the requirements of EN 649 or EN 651 are suitable for special wet areas when they meet the additional requirements specified in Table 1. Table 1 Products suit
28、able for special wet areas CharacteristicIdentity code W1 Identity code W2 Identity code W3 Test method Floor covering type 1)Floor coverings conforming to EN 649 Floor coverings conforming to EN 649 Floor coverings conforming to EN 651 Substrate type 2)Category ACategory BCategory A Overall thickne
29、ss Nominal mm? 1,5? 2,0 EN 428 Total thickness of compact layers mmAs for overall thickness As for overall thickness ? 1,0EN 429 Spreading of water (days)-? 7EN 661 Seam strength when welded to the manufacturers instruction N/50 mm ? 240? 400? 240EN 684 FlexibilityWhen bent around a mandrel of 10 mm
30、 diameter, no cracking or other surface deterioration shall be visible with the naked eye For heterogeneous materials the test shall be made with the surface side as well as the reverse side outwards. EN 435 WatertightnessThe welded product shall be classified watertight.Annex A 1) For installation
31、see annex C 2) For choice of category see annex B 4.3 Installation See annex C. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13553:2002 (E) 6 5 Marking Floor coverings covered by this standard and/or their packaging shall bear the foll
32、owing marking in addition to the marking according to EN 649 or EN 651: a) number and date of this European Standard (EN 13553); b) identity code W1, W2 or W3; c) category A or B. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13553:2002
33、 (E) 7 Annex A (normative) Watertightness test A.1 Scope This annex describes a method for testing the watertightness of floor coverings. A.2 Apparatus A.2.1 A base of non porous material such as metal or glass, on which the sample rests during testing. NOTEIf the base is transparent and suitably su
34、pported, it will enable any leakage to be observed from below. A.2.2 A watertight, bottomless box-frame, to be placed on top of the test specimen. The box shall have vertical sides of at least 300 mm and shall cover a surface area of at least 300 mm ? 500 mm. The box will be supporting water pressur
35、e and should therefore be held in place by clamps or weights. The box-frame shall be sealed to achieve watertightness between the floor covering and the box frame. A.2.3 Indicator paper, sensitive to moisture. A.3 Test specimen The test specimen shall be flat or capable of being flattened so that it
36、 lies flat on the base. The base may be covered by polyethylene foil or similar material. When preparing test specimens the manufacturers instructions shall be observed. The size of the specimen shall be at least 500 mm ? 800 mm and it shall be provided with seams welded in accordance with the manuf
37、acturers recommendations, (see figure A.1). Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13553:2002 (E) 8 Dimensions in millimetres 800 200100 500 200 400 1 Key 1 Welded seam Figure A.1 Specimen with welded seams A.4 Conditioning Speci
38、al conditioning is not required. The test specimen shall be dry on visual inspection and be at a temperature of 15 C to 25 C. A.5 Testing The temperature of the water during testing shall be 15 C to 25 C. Cover the supporting base with the indicator paper. Place the test specimen on the indicator pa
39、per with the use surface side upwards. Place the box over the test specimen and press the support towards the box to ensure watertightness (see A.2.2 and Figure A.2). Fill the box with water to a level of 200 mm ? 10 mm above the upper surface of the test specimen. This water level is maintained for
40、 24 h ? 1 h after which the water is drained off. The moisture indicator and the test specimen are examined for any signs of water penetrating the specimen. The test specimen is considered watertight if there is no sign of penetrating water. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:
41、35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13553:2002 (E) 9 Dimensions in millimetres 100 200 400 250 1 Key 1 Position of box frame on specimen Figure A.2 Position of box frame on specimen A.6 Test report The test report shall contain the following information: a) reference to this method i
42、.e. EN 13553:2002, annex A; b) the material tested (type, source, colour and manufacturers reference numbers); c) preparation of the sample for testing; d) result of the inspection according to A.5. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c
43、) BSI EN 13553:2002 (E) 10 Annex B (informative) Choice of floor covering category The choice of category should be made according to national codes of practice. If a code of practice does not exist the criteria of choice should be the following: Category A : For use on all substrates where traffic
44、intensity or risk of mechanical damage is normal. Category B : For use on all substrates where traffic intensity or risk of mechanical damage is higher than normal. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13553:2002 (E) 11 Annex C
45、 (informative) Installation Products according to this standard should be installed according to the manufacturers instructions for wet area installation for the product, and any national codes of practice. The installations should be carried out by an installer skilled in wet area installations and
46、 in a manner that ensures a correct installation. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13553:2002 (E) 12 Annex D (informative) Determination of elongation at break as an optional property D.1 Apparatus, sampling and preparation
47、 of test pieces As specified in EN 684. D.2 Procedure As for clause 7 of EN 684:1995 but with the additional measurement of length of the test piece at break. D.3 Calculation and expression of result D.3.1Calculate the elongation at break for each test piece as follows: ? 0 01 100)( L LL? ? where ?i
48、s the elongation at break in %; L0is the test length between jaws (100 mm 0,5 mm); L1 is the test length at break. D.3.2Calculate the mean value of the five tests and express the result to the nearest 1 % of the distance between jaws. Also record the minimum of the individual values. D.4 Requirement
49、 If tested, elongation at break shall be ? 15% for each value. D.5 Test report The test report shall contain the following information: a) reference to this test method, EN 13553:2002, annex D; b) complete identification of the product tested, including type, source, colour and manufacturers reference numbers; c) previous history of the sample; d) description of the welding process; e) mean value of the elongation at break; Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 12:35:59
链接地址:https://www.31doc.com/p-3739018.html