BS-EN-1715-3-2008.pdf
《BS-EN-1715-3-2008.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1715-3-2008.pdf(10页珍藏版)》请在三一文库上搜索。
1、BS EN 1715-3:2008 ICS 77.150.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Aluminium and aluminium alloys Drawing stock Part 3: Specific requirements for mechanical uses (excluding welding) Licensed Copy: London South Bank University, South Bank Universit
2、y, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 2008 BSI 2008 ISBN 978 0 580 57007 0 Amendments/corrigenda issued since publication DateComments BS EN 1715-3:2008 National foreword This Briti
3、sh Standard is the UK implementation of . It supersedes BS EN 1715-3:1998 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organizations represented on this committee can be obtained on request to its se
4、cretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. December Licensed Copy: London South Bank University, South Bank Univ
5、ersity, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:2008BS EN 1715-3:2008 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1715-3 April 2008 ICS 77.150.10Supersedes EN 1715-3:1997 English Version Aluminium and aluminium alloys - Drawing stock - Part 3: Specific req
6、uirements for mechanical uses (excluding welding) Aluminium et alliages daluminium - Fil machine - Partie 3: Exigences spcifiques relatives aux applications mcaniques (soudage except) Aluminium und Aluminiumlegierungen - Vordraht - Teil 3: Besondere Anforderungen fr mechanische Anwendungen (ausgenom
7、men Schweien) This European Standard was approved by CEN on 14 March 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliog
8、raphical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of
9、 a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Irela
10、nd, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart,
11、 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1715-3:2008: E Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:2
12、008BS EN 1715-3:2008 EN 1715-3:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 Requirements.4 3.1 Chemical composition 4 3.2 Temper for delivery6 4 Product inspection and testing methods6 4.1 Chemical composition 6 4.2 Mechanical properties.6 5 Delivery documents and inspectio
13、n documents6 6 Marking and packaging.7 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:2008BS EN 1715-3:2008 EN 1715-3:2008 (E) 3 Foreword This document (EN 1715-3:2008) has been prepared by Technical Comm
14、ittee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall
15、 be withdrawn at the latest by October 2008. This document supersedes EN 1715-3:1997. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 4 “Wires and drawing stock“ to revise EN 1715-3:1997. Besides editorial adjustments in the text and update of normative reference
16、s, the following changes have been made: Clause 3: amended; Table 1: values modified, alloy EN AW-5086 deleted, alloy EN AW-6056 added, new tempers for alloys EN AW-6060, EN AW-6061 and EN AW-6082 added EN 1715 comprises the following parts under the general title “Aluminium and aluminium alloys Dra
17、wing stock“: Part 1: General requirements and technical conditions for inspection and delivery Part 2: Specific requirements for electrical applications Part 3: Specific requirements for mechanical uses (excluding welding) Part 4: Specific requirements for welding applications Part 5: Specific requi
18、rements for aluminium food packaging1) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms that it is its policy that in the case when
19、 a patentee refuses to grant licenses on standardised standard products under reasonable and not discriminatory conditions, then this product is removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries
20、 are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, S
21、weden, Switzerland and the United Kingdom. 1) Under preparation. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:12, Uncontrolled Copy, (c) BSI BS EN 1715-3:2008BS EN 1715-3:2008BS EN 1715-3:2008 EN 1715-3:2008 (E) 4 1 Scope This European Standard specifies specific
22、 requirements for drawing stock of aluminium and aluminium alloys for general mechanical uses (excluding welding). The general requirements and technical conditions for inspection and delivery are specified in EN 1715-1. This European Standard does not apply to drawn wire. 2 Normative references The
23、 following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys Wrought produ
24、cts Temper designations EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition and form of products EN 1715-1, Aluminium and aluminium alloys Drawing stock Part 1: General requirements and technical conditions for inspection and delive
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 1715 2008
链接地址:https://www.31doc.com/p-3739023.html