《BS-EN-1360-1997.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1360-1997.pdf(14页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1360:1997 Rubber hoses and hose assemblies for measured fuel dispensing Specification This European Standard EN 1360:1996 has the status of a British Standard ICS 75.200; 83.140.40 Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:02:17 GMT+00:00 2006, Uncontrolled Cop
2、y, (c) BSI BS EN 1360:1997 This British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 June 1997 BSI 02-1999 The following BSI references relate to the work on th
3、is standard: Committee reference PRI/66 Draft for comment 93/312306 DC ISBN 0 580 27384 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies, upon which the follo
4、wing bodies were represented: Association of Metropolitan Authorities British Coal Corporation British Compressed Gases Association British Rubber Manufacturers Association Ltd. Chief and Assistant Chief Fire Officers Association Energy Industries Council Fire Extinguishing Trades Association Home O
5、ffice London Fire and Civil Defence Authority Ministry of Defence RAPRA Technology Ltd. Society of Motor Manufacturers and Traders Limited The following bodies were also represented in the drafting of the standard, through a subcommittee: British Fluid Power Association Chemical Industries Associati
6、on Health and Safety Executive Institute of Petroleum LP Gas Association Petrol Pump Manufacturers Association United Kingdom Petroleum Industry Association Ltd. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:02:17 GMT+00:00 2006, U
7、ncontrolled Copy, (c) BSI BS EN 1360:1997 BSI 02-1999i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 13603 List of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:02:17 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
8、BS EN 1360:1997 ii BSI 02-1999 National foreword This British Standard has been prepared by Technical Committee PRI/66 and is the English language version of EN 1360:1996 Rubber hoses and hose assemblies for measured fuel dispensing Specification. It supersedes BS 3395:1989 which is withdrawn. EN 13
9、60:1996 has been approved by CEN member bodies under the weighted voting procedures introduced in 1988 to coincide with the introduction of the “New Approach” Directives from the Commission of the European Community. A British Standard does not purport to include all the necessary provisions of a co
10、ntract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references Publication referred toCorresponding British Standard EN ISO 1307BS EN ISO 1307:1996 Rubber and plastics ho
11、ses for general-purpose industrial applications Bore diameters and tolerances and tolerances on length EN 24672BS EN 24672:1993 Rubber and plastics hoses Sub-ambient temperature flexibility tests EN 26801BS EN 26801:1993 Rubber and plastics hoses Determination of volumetric expansion EN 27326BS EN 2
12、7326:1993 Rubber and plastics hoses Assessment of ozone resistance under static conditions EN 28031BS EN 28031:1993 Rubber and plastics hoses and hose assemblies Determination of electrical resistance ISO 37BS 903 Physical testing of rubber Part A2:1995 Method for determination of tensile stress-str
13、ain properties ISO 188Part A19:1986 Heat resistance and accelerated ageing tests ISO 1402BS EN ISO 1402:1997 Rubber and plastics hoses and hose assemblies Hydrostatic testing ISO 1746BS EN 21746:1993 Rubber and plastics hoses and tubing Bending tests BS 903 Physical testing of rubber ISO 1817Part A1
14、6:1987 Determination of the effect of liquids ISO 4649Part A9:1988 Determination of abrasion resistance ISO 8033BS EN 28033:1993 Rubber and plastics hose Determination of abrasion between components Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN
15、 title page, pages 2 to 8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:02:17 GMT
16、+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1360 November 1996 ICS 23.040.70 Descriptors: Rubber hoses, plastic tubes, hoses, fuel handling equipment, specification, pressure, dimensions, dimensional tolerances, physical properties, tests, marking Eng
17、lish version Rubber hoses and hose assemblies for measured fuel dispensing Specification Tuyaux et flexibles en caoutchouc pour distribution mesure de carburants Spcification Zapfstellenschluche und -schlauchleitungen aus Gummi Anforderungen This European Standard was approved by CEN on 1996-07-04.
18、CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on a
19、pplication to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat h
20、as the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Sta
21、ndardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 All rights of reproduction and communication in any form and by any means reserved to CEN and its members Ref. No. EN 1360:1996 E Licensed Copy: sheffieldun sheffi
22、eldun, na, Mon Oct 30 05:02:17 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1360:1996 BSI 02-1999 2 Foreword This European Standard has been prepared by Technical Committee CEN/TC 218, Rubber and plastics hoses and hose assemblies, the secretariat of which is held by BSI. This European Standard sha
23、ll be given the status of a national standard, either by publication of an identical text, or by endorsement, at the latest by May 1997, and conflicting national standards shall be withdrawn at the latest by May 1997. According to the CEN/CENELEC Internal Regulations, the national standards organiza
24、tions of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Contents Page Foreword2 1Scope3 2Normative r
25、eferences3 3Materials and construction3 4Pressure requirements3 5Dimensions and tolerances3 5.1Internal diameters3 5.2Minimum thickness of lining and cover3 5.3Cut lengths3 6Physical properties4 7Electrical resistance of assemblies4 8Frequency of testing4 9Marking4 9.1Hoses4 9.2Assemblies4 9.3Short
26、length assemblies (less than 2 m)4 Annex A (normative) End-fitting pull-off test7 Annex B (normative) Method for determination of adhesion between components7 Annex C (informative) A-deviation7 Table 1 Nominal bore, internal diameters and tolerances4 Table 2 Physical properties of hose5 Table 3 Mini
27、mum test frequency6 Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:02:17 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1360:1996 BSI 02-19993 1 Scope This European Standard specifies requirements for three types of rubber hoses and hose assemblies used for measured fuel dispensing, includ
28、ing oxygenated fuels (up to a maximum of 15 % oxygenated compounds). The three types of hoses are as follows: a) type 1: hoses with textile reinforcement suitable for reeling on a drum or hanging in bends; b) type 2: hoses with textile and helical wire reinforcement designed for torsional flexibilit
29、y, suitable for coiling, reeling on a drum or hanging in bends; c) type 3: hoses with fine wire reinforcement designed for low dilation, suitable for reeling on a drum or hanging in bends. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other
30、 publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or r
31、evision. For undated references the latest edition of the publication referred to applies. EN ISO 1307, Rubber and plastics hoses for general purpose industrial applications Bore diameters and tolerances and tolerances on length. (ISO 1307:1992) EN 24672, Rubber and plastics hoses Sub-ambient temper
32、ature flexibility tests. (ISO 4672:1988) EN 26801, Rubber or plastics hoses Determination of volumetric expansion. (ISO 6801:1983) EN 27326, Rubber and plastics hoses Assessment of ozone resistance under static conditions. (ISO 7326:1991) EN 28031, Rubber and plastics hoses and hose assemblies Deter
33、mination of electrical resistance. (ISO 8031:1987) ISO 37, Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties. ISO 188, Rubber, vulcanized Accelerated ageing or heat-resistance tests. ISO 1402, Rubber and plastics hoses and hose assemblies Hydrostatic testing. ISO
34、1746, Rubber or plastics hoses and tubing Bending tests. ISO 1817, Rubber, vulcanized Determination of the effect of liquids. ISO 4649, Rubber Determination of abrasion resistance using a rotating cylindrical drum device. ISO 8033, Rubber and plastics hose Determination of adhesion between component
35、s. 3 Materials and construction The hose shall consist of the following: a smooth, fuel resistant lining of rubber or thermoplastic elastomer (TPE); a suitable reinforcement; a non-corrugated, fuel and weather-resistant rubber or TPE cover. Coupled hose assemblies shall be capable of conducting an e
36、lectrical charge from coupling to coupling. When this capability is provided by means of metallic wires, not less than two (crossed) metallic bonding wires shall be embedded in the hose, and the metal used shall have a high resistance to fatigue, work hardening and corrosion. Hoses with metallic wir
37、es for electrical conductivity shall be designated “M” and using conductive compounds shall be designated “”, the relevant mark being branded on the hose (see clause 9). NOTEOnly non re-usable corrosion resistant couplings should be used for this application. 4 Pressure requirements For all types of
38、 hoses the following shall apply: 5 Dimensions and tolerances 5.1 Internal diameters The internal diameter of the hose shall comply with the dimensions given in Table 1. 5.2 Minimum thickness of lining and cover The thickness of the lining shall be not less than 1,6 mm. The thickness of the cover sh
39、all be not less than 1,0 mm. 5.3 Cut lengths For cut lengths, the tolerances on length shall comply with EN ISO 1307. maximum working pressure16 bara; proof pressure24 bar; minimum bursting pressure48 bar. a 1 bar = 0,1 MPa Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:02:17 GMT+00:00 20
40、06, Uncontrolled Copy, (c) BSI EN 1360:1996 4 BSI 02-1999 Table 1 Nominal bore, internal diameters and tolerances 6 Physical properties The physical properties of the hose shall comply with the requirements given in Table 2 when tested by the methods indicated in Table 2. 7 Electrical resistance of
41、assemblies When tested using the method described in EN 28031, the electrical resistance of an assembly from fitting to fitting shall be not more than 106 . 8 Frequency of testing Minimum frequencies of testing shall comply with schedule given in Table 3. Type approval tests are those tests required
42、 to obtain type approval. Production acceptance tests are those carried out per batch. A batch is defined as either 10 000 m of hose or 5 000 kg of lining and/or cover compound. Routine tests are those carried out on each finished length of hose or hose assembly. 9 Marking 9.1 Hoses The hose shall b
43、e marked legibly and indelibly during the manufacturing process. Marking shall be repeated at least at 2 m intervals, and shall include, at least, the following information: a) manufacturers name or identification, e.g. XYZ; b) number of this European Standard, i.e EN 1360; c) type, e.g. 1; d) nomin
44、al bore, e.g. 19; e) maximum working pressure, in bar, e.g. 16; f) means of electrical conductivity, i.e. M or ; g) quarter and year of manufacture, e.g. 3Q96. EXAMPLE: XYZ/EN 1360/1/19/16/M/3Q96. 9.2 Assemblies over 2 m Each coupling shall be marked with the following information: a) hose assembly
45、manufacturers name or identification; b) month and year of assembly. 9.3 Short length assemblies (less than 2 m) In cases where the marking in 9.1 is not complete on the length of the hose, this information shall be marked on each coupling. Nominal boreInternal diameter mm Tolerances mm 12 16 19 12,
46、5 16,0 19,0 0,8 21 25 32 38 40 21,0 25,0 32,0 38,0 40,0 1,25 NOTEOther internal diameters may be agreed between customer and manufacturer. Licensed Copy: sheffieldun sheffieldun, na, Mon Oct 30 05:02:17 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 1360:1996 BSI 02-19995 Table 2 Physical properties
47、of hose PropertyUnitRequirementTest pieceMethod of test Proof pressureNo leakage or other signs of weakness Full length of hose or hose assembly ISO 1402 Proof test pressure Burst pressure, min.bar48Short length cut from hose or hose assembly ISO 1402 Burst pressure Volumetric expansion, max. Types
48、1 and 2 Type 3 % 2 1 Hydrostatic test pieceEN 26801 Test pressure 3 bar (0,3 MPa) Adhesion between components on a) unaged hoses, min. b) ages hose, min. kN/m2,4 1,8 Short length cut from hoseISO 8033 (for conditioning see annex B) Ambient temperature flexibilityShort length cut from hoseISO 1746 No
49、minal diameter C = 10x nominal bore Low temperture flexibilityNo cracks or breaks Short length cut from hoseEN 24672 (Method B) Test temperature 25 C ( 40 C if requested) (see Note 1) Tensile strength, min lining cover MPaRubberTPETest piece cut from hose or from test sheet (see Note 2) ISO 37 7 7 12 12 Elongation at break, min. lining cover % RubberTPETest piece cut from hose or from test sheet (see Note 2) ISO 37 250 250 350 350 Accelerated ageing Tensile strength change for lini
链接地址:https://www.31doc.com/p-3739075.html