BS-EN-1504-6-2006.pdf
《BS-EN-1504-6-2006.pdf》由会员分享,可在线阅读,更多相关《BS-EN-1504-6-2006.pdf(24页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1504-6:2006 Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conformity Part 6: Anchoring of reinforcing steel bar The European Standard EN 1504-6:2006 has the status of a British Standard IC
2、S 91.080.40 ? BS EN 1504-6:2006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006 ISBN 0 580 49246 X National foreword This British Standard was published by BSI. It is the UK implementation of EN 1504-6:2006. The UK
3、participation in its preparation was entrusted by Technical Committee B/517, Concrete, to Subcommittee B/517/8, Protection and repair of concrete structures. A list of organizations represented on B/517/8 can be obtained on request to its secretary. This publication does not purport to include all t
4、he necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1504-6 August 200
5、6 ICS 91.080.40 English Version Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 6: Anchoring of reinforcing steel bar Produits et systmes pour la protection et la rparation des structures en bt
6、on - Dfinitions, exigences, matrise de la qualit et valuation de la conformit - Partie 6 : Ancrage darmature Produkte und Systeme fr den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualittsberwachung und Beurteilung der Konformitt - Teil 6: Verankerung von Bewehr
7、ungsstben This European Standard was approved by CEN on 19 July 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographi
8、cal references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN
9、member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
10、Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels
11、 2006 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1504-6:2006: E EN 1504-6:2006 (E) 2 Contents Page Foreword3 1 Scope 5 2 Normative references5 3 Terms and definitions .6 4 Performance characteristics for intended uses.6 5 Requi
12、rements.7 5.1 Identification requirements.7 5.2 Performance requirements.7 5.3 Release of dangerous substances.8 5.4 Reaction to fire.8 6 Sampling.8 7 Evaluation of conformity.8 7.1 General8 7.2 Initial type testing 8 7.3 Factory production control.9 7.4 Assessment, surveillance and certification of
13、 factory production control (informative)9 8 Marking and labelling9 Annex A (informative) Minimum frequency of testing for factory production control.10 Annex B (informative) Release of dangerous substances11 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the E
14、U Construction Products Directive12 ZA1 Scope and relevant characteristics .12 ZA.2 Attestation of conformity14 ZA.3 CE marking and labelling19 EN 1504-6:2006 (E) 3 Foreword This document (EN 1504-6:2006) has been prepared by Technical Committee CEN/TC 104 “Concrete and related products”, the secret
15、ariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2007, and conflicting national standards shall be withdrawn at the latest by December 2008. It has been deve
16、loped by sub-committee 8 “Products and systems for the protection and repair of concrete structures“ (Secretariat AFNOR). This Part of EN 1504 does not supersede any other European Standard. This document has been prepared under a mandate given to CEN by the European Commission and the European Free
17、 Trade Association and supports essential requirements of EU Construction Products Directive (89/106/EC). For the relationship with the EU Directive, see informative Annex ZA, which is an integral part of this document. This Part of EN 1504 includes an informative Annex A dealing with factory produc
18、tion control and an informative Annex B dealing with release of dangerous substances. This Part of this European Standard is one of the Parts of this standard on products and systems for the repair and protection of concrete structures. The other parts are listed below: EN 1504-1, Products and syste
19、ms for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conformity Part 1: Definitions. EN 1504-2, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of confo
20、rmity Part 2: Surface protection systems for concrete. EN 1504-3, Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 3: Structural and non-structural repair. EN 1504-4, Products and systems for th
21、e protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conformity Part 4: Structural bonding. EN 1504-5, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conform
22、ity Part 5: Concrete injection. EN 1504-7, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conformity Part 7: Reinforcement corrosion protection. EN 1504-8, Products and systems for the protection and repair of co
23、ncrete structures Definitions, requirements, quality control and evaluation of conformity Part 8: Quality control and evaluation of conformity. EN 1504-6:2006 (E) 4 ENV 1504-9 1), Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and
24、 evaluation of conformity Part 9: General principles for the use of products and systems. EN 1504-10, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and evaluation of conformity - Part 10: Site application of products and systems
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 1504 2006
链接地址:https://www.31doc.com/p-3739459.html