《BS-EN-130101-1998.pdf》由会员分享,可在线阅读,更多相关《BS-EN-130101-1998.pdf(14页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 130101:1998 Harmonized system of quality assessment for electronic components Blank detail specification: Fixed polyethylene- terephtalate film dielectric metal foil capacitors for direct current Assessment level E The European Standard EN 130101:1997 has the status of a Briti
2、sh Standard ICS 31.060.30 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 130101:1998 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standa
3、rds Board and comes into effect on 15 February 1998 BSI 04-1999 ISBN 0 580 29114 6 National foreword This British Standard is the English language version of EN 130101:1997 published by the European Electrotechnical Components Committee (CECC) of the European Committee for Electronic Standardization
4、 (CENELEC). It supersedes BS CECC 30101:1988 which will be withdrawn on 1998-04-01. The UK participation in its preparation was entrusted by Technical Committee EPL/40, Capacitors and resistors for electronic equipment, to Subcommittee EPL/40/1, Capacitors and EMI suppression components for electron
5、ic equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments a
6、nd promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications
7、with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standar
8、ds Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages
9、 This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 9 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amen
10、dments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 130101:1998 BSI 04-1999i Contents Page National forewordInside front cover Foreword2 Text of EN 1301013 Licensed Copy: sheffieldun she
11、ffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 130101 October 1997 ICSSupersedes CECC 30 101:1985 and
12、 its amendments Descriptors: English version Blank Detail Specification: Fixed polyethylene-terephtalate film dielectric metal foil capacitors for direct current Assessment level E This European Standard was approved by CENELEC on 1992-10-14. CENELEC members are bound to comply with the CEN/CENELEC
13、Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENEL
14、EC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
15、CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardizat
16、ion Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 130101:1997 E License
17、d Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130101:1997 BSI 04-1999 2 Foreword At the request of CLC/TC CECC/SC 40XA (former WG 3), the text of CECC 30 101:1985, Issue 2, with its amendments A1 through A4 and document CECC(Secretariat)3063,
18、was submitted to the formal vote for conversion, ion into a European Standard. The text of the draft, together with the voting report, circulated as document CECC(Secretariat)3201, was approved as EN 130101 on 1992-10-14 and confirmed by CENELEC on 1997-03-11. The following dates were fixed: Content
19、s Page Foreword2 1General data4 2Inspection requirements5 Table 14 Table 2 Values of capacitance related to voltages and case sizes4 Table 3 Other characteristics5 Table 4A Lot-by-lot inspection (Group A and B)6 Table 4B Periodic tests7 latest date by which the EN has to be implemented at national l
20、evel by publication of an identical national standard or by endorsement(dop) 1998-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow) 1998-04-01 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
21、EN 130101:1997 BSI 04-19993 Identification of the detail specification (DS) and the component The first page of the DS should have the layout recommended as follows. The numbers in square brackets correspond to the indications to be completed thereunder. 1 The name of the National Standards Organiza
22、tion under whose authority the DS is published and, if applicable, the organization from whom the DS is available. 2 The CECC symbol and the number allotted to the DS by the CECC General Secretariat. 3 The number and issue number of the CECC generic and sectional specification as relevant; also nati
23、onal reference if different. 4 If different from the CECC number, the national number of the DS, date of issue and any further information required by the national system, together with any amendment numbers. 5 A brief description of the component or range of components. 6 Information on typical con
24、struction (where applicable); for example: metal film helically cut. For 5 and 6 the text to be given in the DS should be suitable for an entry in the Register of Approvals CECC 00200 and CECC 00300 (Library List). 7 An outline drawing with main dimensions which are of importance for interchangeabil
25、ity, and/or reference to the appropriate national or international document for outlines. Alternatively, this drawing may be given in an annex to the DS, but 7 should always contain an illustration of the general outer appearance of the component. 8 The level(s) of quality assessment covered by the
26、DS. 9 Reference data giving information on the most important properties of the component which allow comparison between the various component types intended for the same, or for similar, applications. Specification available from: (National Standards Organization) 1CECC number and mark2 ELECTRONIC
27、COMPONENTS OF ASSESSED QUALITY DETAIL SPECIFICATION IN ACCORDANCE WITH: (Number of national generic and sectional specification) 3(National number of detail specification, date of issue, National type number, if any) 4 Outline and dimensions: (first angle projection) 7DETAIL SPECIFICATION FOR FIXED
28、POLYETHYLENE-TEREPHTHALATE FILM DIELECTRIC METAL FOIL D.C. CAPACITORS 5 TYPICAL CONSTRUCTION: (Examples) 6 cylindrical/rectangular non metallic/metallic case insulated/non insulated axial/radial terminations Assessment level E8 QUICK REFERENCE DATA: Rated capacitance range, capacitance tolerance, d.
29、c. rated voltage range, climatic category, performance grade 9 Information about manufacturers who have components qualified to this detail specification is available in the current Register of Approvals CECC 00200 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncon
30、trolled Copy, (c) BSI EN 130101:1997 4 BSI 04-1999 1 General data 1.1 Method of mounting for vibration and bump or shock tests (Shall be specified in the detail specification). See 1.3.3 of EN 130100:1997. 1.2 Dimensions Table 1 NOTE 1When there is no case size reference, Table 1 may be omitted and
31、the dimensions shall be given in Table 2, which then becomes Table 1. NOTE 2The dimensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. 1.3 Ratings and characteristics Table 2 Values of capacitance related to voltages and case sizes 1.4 Related document 1.5 Marking
32、 The marking of the capacitor and the packing shall be in accordance with the requirements of 1.5 of EN 130100:1997. NOTEThe details of the marking of the component and packing shall be given in full in the detail specification. 1.6 Ordering information Orders for capacitors covered by this specific
33、ation shall contain, in clear or in coded form, the following minimum information: 1) rated capacitance; 2) tolerance on rated capacitance; 3) rated d.c. voltage; Case size reference Dimensions (in mm) FLHd Capacitance range(See Table 2) Tolerance on rated capacitance Rated voltage(See Table 2) Cate
34、gory voltage (if applicable)(See Table 2) Climatic category Rated temperature Max. a.c. voltage (if applicable) Tangent of loss angle Insulation resistance Rated voltage Category voltagea Rated capacitance (in nF and/or F) Case sizeCase sizeCase sizeCase size a If different from the rated voltage Ge
35、neric specification:EN 130000 Sectional specification:EN 130100 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130101:1997 BSI 04-19995 4) number and issue reference of the detail specification and style reference. 1.7 Certified test rec
36、ords Required/not required. 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional specification NOTEAdditions or increased requirements should be specified only when essential. Table 3 Other
37、characteristics 2 Inspection requirements 2.1 Procedures 2.1.1 For qualification approval the procedures shall be in accordance with 3.4 of EN 130100:1997. 2.1.2 For quality conformance inspection the test schedule (Table 4) includes sampling, periodicity, severities and requirements. The formation
38、of inspection lots is covered by 3.5.1 of EN 130100:1997. This table is to be used for defining characteristics which are additional to or tighter than those given in the sectional specification. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) B
39、SI EN 130101:1997 6 BSI 04-1999 Table 4A Lot-by-lot inspection (Group A and B) Clause number and testaConditions of testaILbAQLb % Performance requirementsa Group A1Non-destructive S42,5 4.1Visual examinationAs in 4.1 Legible marking as specified in 1.5 of this specification 4.1Dimensions (gauging)A
40、s specified in Table 1 of this specification Group A2Non-destructive II1,0 4.2.1Voltage proof (Measuring point 1a) No breakdown or flashover 4.2.2Capacitancewithin specified tolerance 4.2.3Tangent of loss angleas in 4.2.3 b) 4.2.4Insulation resistance (Measuring point 1a) as in 4.2.4 b) Group B1Dest
41、ructivecdS32,5 4.5SolderabilityMethod:Good tinning as evidenced by free flowing of the solder with wetting of the terminations or soldering time s, as applicable Ageing:(None or 4 h as 155 C dry heat or other) a Refers to section 4 of EN 130100:1997. b Inspection levels (IQ) and Acceptable Quality L
42、evels (AQL) are selected from IEC 60410. c Provided that requirements of group A1 are met after testing. d Capacitors which have been submitted to the tests of group B1 may be released provided they have not been submitted to ageing and are resubmitted to the tests of group A and pass those tests. I
43、t is permitted to submit electrically defective capacitors or detached terminations instead of completed capacitors to this test provided they have been subjected to the same process treatments as a completed capacitor. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006,
44、Uncontrolled Copy, (c) BSI EN 130101:1997 BSI 04-19997 Table 4B Periodic tests Clause number and testaCondition of testaPbnbCbPerformance requirementsa Group C1ADestructive691 4.1Dimensions (Detail)See detail specifications 4.3Robustness of terminations Visual examinationNo visible damage 4.4Resista
45、nce to soldering heat No pre-drying Method: (1A or 1B) 4.4.2Initial measurements Capacitance Tangent or loss angle 4.4.3Final measurements Visual examinationNo visible damage Capacitance of the value measured initially Group C1BDestructive6181 4.6.2Initial measurements Capacitance Tangent of loss an
46、gle Insulation resistance: method 4.6Rapid change of temperature TA = Lower category temperature TB = Upper category temperature Five cycles Duration t = 30 min Visual examinationNo visible damage 4.7VibrationMethod of mounting: See 1.1 of this specification. Procedure: Endurance by sweeping Frequen
47、cy range: . Hz to . Hz Amplitude 0,75 mm or acceleration 98 m/s2 (whichever is the lower amplitude) Total sweep cycles Visual examinationNo visible damage 4.8Bump (or shock) (see 4.9) Method of mounting: see 1.1 of this specification Number of bumps: . Acceleration: . m/s2 Duration of pulse: . ms %C
48、 C - 2 % Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:17:31 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 130101:1997 8 BSI 04-1999 Table 4B Periodic tests Clause number and testaCondition of testaPbnbCbPerformance requirementsa 4.9Shock (or bump) (see 4.8) Method of mounting: see 1.1 o
49、f this spec. Acceleration: . m/s2 Duration of pulse: . ms 4.8.4 or 4.9.4 Final measurements Visual examinationNo visible damage Capacitance of value measured in 4.6.2 Tangent of loss angleSee detail specification Group C1Destructive6272 4.10Climatic sequence 4.10.3Dry heatTemperature: Upper category temperature Duration: 16 h 4.10.4Damp, heat, cyclic, test Db, first cycle 4.10.5ColdTemperature: Lower category temperature Duration 2 h 4.10.6Low air pressure (if required by the detail
链接地址:https://www.31doc.com/p-3739462.html